[PATCH] sim: cfi: new flash device simulation

[PATCH] sim: cfi: new flash device simulation

[Mike Frysinger]

This simulates a CFI flash.  Its pretty configurable via the device
tree.  For now, only basic read/write/erase operations are supported
for the Intel command set, but it's easy enough to extend support.
It's certainly enough to trick Das U-Boot into using it for probing,
reading, writing, and erasing.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

2010-12-30  Mike Frysinger  <vapier@gentoo.org>

	* aclocal.m4 (SIM_AC_OPTION_HARDWARE): Add cfi to default list.
	* Make-common.in (dv-cfi.o): New rule.
	* dv-cfi.c, dv-cfi.h: New files.
---
 sim/common/Make-common.in |    3 +
 sim/common/aclocal.m4     |    2 +-
 sim/common/dv-cfi.c       |  704 +++++++++++++++++++++++++++++++++++++++++++++
 sim/common/dv-cfi.h       |   60 ++++
 4 files changed, 768 insertions(+), 1 deletions(-)
 create mode 100644 sim/common/dv-cfi.c
 create mode 100644 sim/common/dv-cfi.h

diff --git a/sim/common/Make-common.in b/sim/common/Make-common.in
index 54973ce..a83650d 100644
--- a/sim/common/Make-common.in
+++ b/sim/common/Make-common.in
@@ -579,6 +579,9 @@ hw-tree.o: $(srccom)/hw-tree.c $(hw_main_headers) $(hw-tree_h)
 
 # Devices.
 
+dv-cfi.o: $(srccom)/dv-cfi.c $(hw_main_headers) $(sim_main_headers)
+	$(CC) -c $(srccom)/dv-cfi.c $(ALL_CFLAGS)
+
 dv-core.o: $(srccom)/dv-core.c $(hw_main_headers) $(sim_main_headers)
 	$(CC) -c $(srccom)/dv-core.c $(ALL_CFLAGS)
 
diff --git a/sim/common/aclocal.m4 b/sim/common/aclocal.m4
index bda20ce..cec0155 100644
--- a/sim/common/aclocal.m4
+++ b/sim/common/aclocal.m4
@@ -573,7 +573,7 @@ fi
 if test "[$2]"; then
   hardware="[$2]"
 else
-  hardware="core pal glue"
+  hardware="cfi core pal glue"
 fi
 hardware="$hardware [$3]"
 sim_hw_cflags="-DWITH_HW=1"
diff --git a/sim/common/dv-cfi.c b/sim/common/dv-cfi.c
new file mode 100644
index 0000000..71f04f8
--- /dev/null
+++ b/sim/common/dv-cfi.c
@@ -0,0 +1,704 @@
+/* Common Flash Memory Interface (CFI) model.
+   http://www.spansion.com/Support/AppNotes/CFI_Spec_AN_03.pdf
+   http://www.spansion.com/Support/AppNotes/cfi_100_20011201.pdf
+
+   Copyright (C) 2010 Free Software Foundation, Inc.
+   Contributed by Analog Devices, Inc.
+
+   This file is part of simulators.
+
+   This program is free software; you can redistribute it and/or modify
+   it under the terms of the GNU General Public License as published by
+   the Free Software Foundation; either version 3 of the License, or
+   (at your option) any later version.
+
+   This program is distributed in the hope that it will be useful,
+   but WITHOUT ANY WARRANTY; without even the implied warranty of
+   MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+   GNU General Public License for more details.
+
+   You should have received a copy of the GNU General Public License
+   along with this program.  If not, see <http://www.gnu.org/licenses/>.  */
+
+/* TODO: support vendor query tables.  */
+
+#include "config.h"
+
+#include <math.h>
+#include <errno.h>
+#include <fcntl.h>
+#include <unistd.h>
+#ifdef HAVE_SYS_MMAN_H
+#include <sys/mman.h>
+#endif
+
+#include "sim-main.h"
+#include "devices.h"
+#include "dv-cfi.h"
+
+enum cfi_state
+{
+  CFI_STATE_READ,
+  CFI_STATE_READ_ID,
+  CFI_STATE_CFI_QUERY,
+  CFI_STATE_PROTECT,
+  CFI_STATE_STATUS,
+  CFI_STATE_ERASE,
+  CFI_STATE_WRITE,
+  CFI_STATE_WRITE_BUFFER,
+  CFI_STATE_WRITE_BUFFER_CONFIRM,
+};
+
+struct cfi_query
+{
+  unsigned char qry[3];
+  unsigned char p_id[2];
+  unsigned char p_adr[2];
+  unsigned char a_id[2];
+  unsigned char a_adr[2];
+  union {
+    unsigned char voltages[4];
+    struct {
+      unsigned char vcc_min;
+      unsigned char vcc_max;
+      unsigned char vpp_min;
+      unsigned char vpp_max;
+    };
+  };
+  union {
+    unsigned char timeouts[8];
+    struct {
+      unsigned char timeout_typ_unit_write;
+      unsigned char timeout_typ_buf_write;
+      unsigned char timeout_typ_block_erase;
+      unsigned char timeout_typ_chip_erase;
+      unsigned char timeout_max_unit_write;
+      unsigned char timeout_max_buf_write;
+      unsigned char timeout_max_block_erase;
+      unsigned char timeout_max_chip_erase;
+    };
+  };
+  unsigned char dev_size;
+  unsigned char iface_desc[2];
+  unsigned char max_buf_write_len[2];
+  unsigned char num_erase_regions;
+  /*unsigned char erase_region_info;*/
+};
+
+struct cfi_erase_region
+{
+  unsigned blocks;
+  unsigned size;
+  unsigned start;
+  unsigned end;
+};
+
+struct cfi;
+
+struct cfi_cmdset
+{
+  unsigned id;
+  void (*setup) (struct hw *me, struct cfi *cfi);
+  bool (*write) (struct hw *me, struct cfi *cfi, const void *source,
+		 unsigned offset, unsigned value, unsigned nr_bytes);
+  bool (*read) (struct hw *me, struct cfi *cfi, void *dest,
+		unsigned offset, unsigned shifted_offset, unsigned nr_bytes);
+};
+
+struct cfi
+{
+  unsigned width, dev_size, status;
+  enum cfi_state state;
+  unsigned char *data, *mmap;
+
+  struct cfi_query query;
+  const struct cfi_cmdset *cmdset;
+
+  unsigned char *erase_region_info;
+  struct cfi_erase_region *erase_regions;
+};
+
+static const char * const state_names[] = {
+  "READ", "READ_ID", "CFI_QUERY", "PROTECT", "STATUS", "ERASE", "WRITE",
+  "WRITE_BUFFER", "WRITE_BUFFER_CONFIRM",
+};
+\f
+static void
+cfi_erase_block (struct hw *me, struct cfi *cfi, unsigned offset)
+{
+  unsigned i;
+  struct cfi_erase_region *region;
+
+  /* If no erase regions, then we can only do whole chip erase.  */
+  /* XXX: Is this within spec ?  Or must there always be at least one ?  */
+  if (!cfi->query.num_erase_regions)
+    memset (cfi->data, 0xff, cfi->dev_size);
+
+  for (i = 0; i < cfi->query.num_erase_regions; ++i)
+    {
+      region = &cfi->erase_regions[i];
+
+      if (offset >= region->end)
+	continue;
+
+      /* XXX: Does spec require the erase addr to be erase block aligned ?
+	      Maybe this is check is overly cautious ...  */
+      offset &= ~(region->size - 1);
+      memset (cfi->data + offset, 0xff, region->size);
+      break;
+    }
+}
+
+static unsigned
+cfi_unshift_addr (struct cfi *cfi, unsigned addr)
+{
+  switch (cfi->width)
+    {
+    case 4: addr >>= 1;
+    case 2: addr >>= 1;
+    }
+  return addr;
+}
+
+static void
+cfi_encode_16bit (unsigned char *data, unsigned num)
+{
+  /* CFI is little endian.  */
+  data[0] = num;
+  data[1] = num >> 8;
+}
+\f
+static bool
+cmdset_intel_write (struct hw *me, struct cfi *cfi, const void *source,
+		    unsigned offset, unsigned value, unsigned nr_bytes)
+{
+  switch (cfi->state)
+    {
+    case CFI_STATE_READ:
+    case CFI_STATE_READ_ID:
+      switch (value)
+	{
+	case INTEL_CMD_ERASE_BLOCK:
+	  cfi->state = CFI_STATE_ERASE;
+	  break;
+	case INTEL_CMD_WRITE:
+	case INTEL_CMD_WRITE_ALT:
+	  cfi->state = CFI_STATE_WRITE;
+	  break;
+	case INTEL_CMD_STATUS_CLEAR:
+	  cfi->status = INTEL_SR_DWS;
+	  break;
+	case INTEL_CMD_LOCK_SETUP:
+	  cfi->state = CFI_STATE_PROTECT;
+	  break;
+	default:
+	  return false;
+	}
+      break;
+
+    case CFI_STATE_ERASE:
+      if (value == INTEL_CMD_ERASE_CONFIRM)
+	{
+	  cfi_erase_block (me, cfi, offset);
+	  cfi->status &= ~(INTEL_SR_PS | INTEL_SR_ES);
+	}
+      else
+	cfi->status |= INTEL_SR_PS | INTEL_SR_ES;
+      cfi->state = CFI_STATE_STATUS;
+      break;
+
+    case CFI_STATE_PROTECT:
+      switch (value)
+	{
+	case INTEL_CMD_LOCK_BLOCK:
+	case INTEL_CMD_UNLOCK_BLOCK:
+	case INTEL_CMD_LOCK_DOWN_BLOCK:
+	  /* XXX: Handle the command.  */
+	  break;
+	default:
+	  /* Kick out.  */
+	  cfi->status |= INTEL_SR_PS | INTEL_SR_ES;
+	  break;
+	}
+      cfi->state = CFI_STATE_STATUS;
+      break;
+
+    default:
+      return false;
+    }
+
+  return true;
+}
+
+static bool
+cmdset_intel_read (struct hw *me, struct cfi *cfi, void *dest,
+		   unsigned offset, unsigned shifted_offset, unsigned nr_bytes)
+{
+  unsigned char *sdest = dest;
+
+  switch (cfi->state)
+    {
+    case CFI_STATE_STATUS:
+    case CFI_STATE_ERASE:
+      *sdest = cfi->status;
+      break;
+
+    case CFI_STATE_READ_ID:
+      switch (shifted_offset & 0x1ff)
+	{
+	case 0x00:	/* Manufacturer Code.  */
+	  cfi_encode_16bit (dest, INTEL_ID_MANU);
+	  break;
+	case 0x01:	/* Device ID Code.  */
+	  /* XXX: Push to device tree ?  */
+	  cfi_encode_16bit (dest, 0xad);
+	  break;
+	case 0x02:	/* Block lock state.  */
+	  /* XXX: This is per-block ...  */
+	  *sdest = 0x00;
+	  break;
+	case 0x05:	/* Read Configuration Register.  */
+	  cfi_encode_16bit (dest, (1 << 15));
+	  break;
+	default:
+	  return false;
+	}
+      break;
+
+    default:
+      return false;
+    }
+
+  return true;
+}
+
+static void
+cmdset_intel_setup (struct hw *me, struct cfi *cfi)
+{
+  cfi->status = INTEL_SR_DWS;
+}
+
+static const struct cfi_cmdset cfi_cmdset_intel = {
+  CFI_CMDSET_INTEL, cmdset_intel_setup, cmdset_intel_write, cmdset_intel_read,
+};
+
+static const struct cfi_cmdset * const cfi_cmdsets[] = {
+  &cfi_cmdset_intel,
+};
+\f
+static unsigned
+cfi_io_write_buffer (struct hw *me, const void *source, int space,
+		     address_word addr, unsigned nr_bytes)
+{
+  struct cfi *cfi = hw_data (me);
+  const unsigned char *ssource = source;
+  enum cfi_state old_state;
+  unsigned offset, shifted_offset, value;
+
+  offset = addr & (cfi->dev_size - 1);
+  shifted_offset = cfi_unshift_addr (cfi, offset);
+
+  if (cfi->width != nr_bytes)
+    {
+      HW_TRACE ((me, "write 0x%08lx length %u does not match flash width %u",
+		 (unsigned long) addr, nr_bytes, cfi->width));
+      return nr_bytes;
+    }
+
+  if (cfi->state == CFI_STATE_WRITE)
+    {
+      /* NOR flash can only go from 1 to 0.  */
+      unsigned i;
+
+      HW_TRACE ((me, "program %#x length %u", offset, nr_bytes));
+
+      for (i = 0; i < nr_bytes; ++i)
+	cfi->data[offset + i] &= ssource[i];
+
+      cfi->state = CFI_STATE_STATUS;
+
+      return nr_bytes;
+    }
+
+  value = ssource[0];
+
+  old_state = cfi->state;
+
+  if (value == CFI_CMD_READ || value == CFI_CMD_RESET)
+    {
+      cfi->state = CFI_STATE_READ;
+      goto done;
+    }
+
+  switch (cfi->state)
+    {
+    case CFI_STATE_READ:
+    case CFI_STATE_READ_ID:
+      if (value == CFI_CMD_CFI_QUERY)
+	{
+	  if (shifted_offset == CFI_ADDR_CFI_QUERY_START)
+	    cfi->state = CFI_STATE_CFI_QUERY;
+	  goto done;
+	}
+
+      if (value == CFI_CMD_READ_ID)
+	{
+	  cfi->state = CFI_STATE_READ_ID;
+	  goto done;
+	}
+
+      /* Fall through.  */
+
+    default:
+      if (!cfi->cmdset->write (me, cfi, source, offset, value, nr_bytes))
+	HW_TRACE ((me, "unhandled command %#x at %#x", value, offset));
+      break;
+    }
+
+ done:
+  HW_TRACE ((me, "write 0x%08lx command {%#x,%#x,%#x,%#x}; state %s -> %s",
+	     (unsigned long) addr, ssource[0],
+	     nr_bytes > 1 ? ssource[1] : 0,
+	     nr_bytes > 2 ? ssource[2] : 0,
+	     nr_bytes > 3 ? ssource[3] : 0,
+	     state_names[old_state], state_names[cfi->state]));
+
+  return nr_bytes;
+}
+
+static unsigned
+cfi_io_read_buffer (struct hw *me, void *dest, int space,
+		    address_word addr, unsigned nr_bytes)
+{
+  struct cfi *cfi = hw_data (me);
+  unsigned char *sdest = dest;
+  unsigned offset, shifted_offset;
+
+  offset = addr & (cfi->dev_size - 1);
+  shifted_offset = cfi_unshift_addr (cfi, offset);
+
+  /* XXX: Is this OK to enforce ?  */
+#if 0
+  if (cfi->state != CFI_STATE_READ && cfi->width != nr_bytes)
+    {
+      HW_TRACE ((me, "read 0x%08lx length %u does not match flash width %u",
+		 (unsigned long) addr, nr_bytes, cfi->width));
+      return nr_bytes;
+    }
+#endif
+
+  HW_TRACE ((me, "%s read 0x%08lx length %u",
+	     state_names[cfi->state], (unsigned long) addr, nr_bytes));
+
+  switch (cfi->state)
+    {
+    case CFI_STATE_READ:
+      memcpy (dest, cfi->data + offset, nr_bytes);
+      break;
+
+    case CFI_STATE_CFI_QUERY:
+      if (shifted_offset >= CFI_ADDR_CFI_QUERY_RESULT &&
+	  shifted_offset < CFI_ADDR_CFI_QUERY_RESULT + sizeof (cfi->query) +
+		     (cfi->query.num_erase_regions * 4))
+	{
+	  unsigned char *qry;
+
+	  shifted_offset -= CFI_ADDR_CFI_QUERY_RESULT;
+	  if (shifted_offset >= sizeof (cfi->query))
+	    {
+	      qry = cfi->erase_region_info;
+	      shifted_offset -= sizeof (cfi->query);
+	    }
+	  else
+	    qry = (void *) &cfi->query;
+
+	  sdest[0] = qry[shifted_offset];
+	  memset (sdest + 1, 0, nr_bytes - 1);
+
+	  break;
+	}
+
+    default:
+      if (!cfi->cmdset->read (me, cfi, dest, offset, shifted_offset, nr_bytes))
+	HW_TRACE ((me, "unhandled state %s", state_names[cfi->state]));
+      break;
+    }
+
+  return nr_bytes;
+}
+
+static void
+cfi_delete_callback (struct hw *me)
+{
+  struct cfi *cfi = hw_data (me);
+
+  if (cfi->mmap)
+    munmap (cfi->mmap, cfi->dev_size);
+}
+
+static void
+cfi_add_erase_region (struct hw *me, struct cfi *cfi,
+		      unsigned blocks, unsigned size)
+{
+  unsigned num_regions = cfi->query.num_erase_regions;
+  struct cfi_erase_region *region;
+  unsigned char *qry_region;
+
+  /* Store for our own usage.  */
+  region = &cfi->erase_regions[num_regions];
+  region->blocks = blocks;
+  region->size = size;
+  if (num_regions == 0)
+    region->start = 0;
+  else
+    region->start = region[-1].end;
+  region->end = region->start + (blocks * size);
+
+  /* Regions are 4 bytes long.  */
+  qry_region = cfi->erase_region_info + 4 * num_regions;
+
+  /* [0][1] = number erase blocks - 1 */
+  if (blocks > 0xffff + 1)
+    hw_abort (me, "erase blocks %u too big to fit into region info", blocks);
+  cfi_encode_16bit (&qry_region[0], blocks - 1);
+
+  /* [2][3] = block size / 256 bytes */
+  if (size > 0xffff * 256)
+    hw_abort (me, "erase size %u too big to fit into region info", size);
+  cfi_encode_16bit (&qry_region[2], size / 256);
+
+  /* Yet another region.  */
+  cfi->query.num_erase_regions = num_regions + 1;
+}
+
+/* Device tree options:
+     Required:
+       .../reg <addr> <len>
+       .../cmdset <primary; integer> [alt; integer]
+     Optional:
+       .../size <device size (must be pow of 2)>
+       .../width <8|16|32>
+       .../write_size <integer (must be pow of 2)>
+       .../erase_regions <number blocks> <block size> \
+                         [<number blocks> <block size> ...]
+       .../voltage <vcc min> <vcc max> <vpp min> <vpp max>
+       .../timeouts <typ unit write>  <typ buf write>  \
+                    <typ block erase> <typ chip erase> \
+                    <max unit write>  <max buf write>  \
+                    <max block erase> <max chip erase>
+       .../file <file> [ro|rw]
+     Defaults:
+       size: <len> from "reg"
+       width: 8
+       write_size: 0 (not supported)
+       erase_region: 1 (can only erase whole chip)
+       voltage: 0.0V (for all)
+       timeouts: typ: 1µs, not supported, 1ms, not supported
+                 max: 1µs, 1ms, 1ms, not supported
+
+  TODO: Verify user args are valid (e.g. voltage is 8 bits).  */
+static void
+attach_cfi_regs (struct hw *me, struct cfi *cfi)
+{
+  address_word attach_address;
+  int attach_space;
+  unsigned attach_size;
+  reg_property_spec reg;
+  bool fd_writable;
+  int i, ret, fd;
+  signed_cell ival;
+
+  if (hw_find_property (me, "reg") == NULL)
+    hw_abort (me, "Missing \"reg\" property");
+  if (hw_find_property (me, "cmdset") == NULL)
+    hw_abort (me, "Missing \"cmdset\" property");
+
+  if (!hw_find_reg_array_property (me, "reg", 0, &reg))
+    hw_abort (me, "\"reg\" property must contain three addr/size entries");
+
+  hw_unit_address_to_attach_address (hw_parent (me),
+				     &reg.address,
+				     &attach_space, &attach_address, me);
+  hw_unit_size_to_attach_size (hw_parent (me), &reg.size, &attach_size, me);
+
+  hw_attach_address (hw_parent (me),
+		     0, attach_space, attach_address, attach_size, me);
+
+  /* Extract the desired flash command set.  */
+  ret = hw_find_integer_array_property (me, "cmdset", 0, &ival);
+  if (ret != 1 && ret != 2)
+    hw_abort (me, "\"cmdset\" property takes 1 or 2 entries");
+  cfi_encode_16bit (cfi->query.p_id, ival);
+
+  for (i = 0; i < ARRAY_SIZE (cfi_cmdsets); ++i)
+    if (cfi_cmdsets[i]->id == ival)
+      cfi->cmdset = cfi_cmdsets[i];
+  if (cfi->cmdset == NULL)
+    hw_abort (me, "cmdset %u not supported", ival);
+
+  if (ret == 2)
+    {
+      hw_find_integer_array_property (me, "cmdset", 1, &ival);
+      cfi_encode_16bit (cfi->query.a_id, ival);
+    }
+
+  /* Extract the desired device size.  */
+  if (hw_find_property (me, "size"))
+    cfi->dev_size = hw_find_integer_property (me, "size");
+  else
+    cfi->dev_size = attach_size;
+  cfi->query.dev_size = log2 (cfi->dev_size);
+
+  /* Extract the desired flash width.  */
+  if (hw_find_property (me, "width"))
+    {
+      cfi->width = hw_find_integer_property (me, "width");
+      if (cfi->width != 8 && cfi->width != 16 && cfi->width != 32)
+	hw_abort (me, "\"width\" must be 8 or 16 or 32, not %u", cfi->width);
+    }
+  else
+    /* Default to 8 bit.  */
+    cfi->width = 8;
+  /* Turn 8/16/32 into 1/2/4.  */
+  cfi->width /= 8;
+
+  /* Extract optional write buffer size.  */
+  if (hw_find_property (me, "write_size"))
+    {
+      ival = hw_find_integer_property (me, "write_size");
+      cfi_encode_16bit (cfi->query.max_buf_write_len, log2 (ival));
+    }
+
+  /* Extract optional erase regions.  */
+  if (hw_find_property (me, "erase_regions"))
+    {
+      ret = hw_find_integer_array_property (me, "erase_regions", 0, &ival);
+      if (ret % 2)
+	hw_abort (me, "\"erase_regions\" must be specified in sets of 2");
+
+      cfi->erase_region_info = HW_NALLOC (me, unsigned char, ret / 2);
+      cfi->erase_regions = HW_NALLOC (me, struct cfi_erase_region, ret / 2);
+
+      for (i = 0; i < ret; i += 2)
+	{
+	  unsigned blocks, size;
+
+	  hw_find_integer_array_property (me, "erase_regions", i, &ival);
+	  blocks = ival;
+
+	  hw_find_integer_array_property (me, "erase_regions", i + 1, &ival);
+	  size = ival;
+
+	  cfi_add_erase_region (me, cfi, blocks, size);
+	}
+    }
+
+  /* Extract optional voltages.  */
+  if (hw_find_property (me, "voltage"))
+    {
+      unsigned num = ARRAY_SIZE (cfi->query.voltages);
+
+      ret = hw_find_integer_array_property (me, "voltage", 0, &ival);
+      if (ret > num)
+	hw_abort (me, "\"voltage\" may have only %u arguments", num);
+
+      for (i = 0; i < ret; ++i)
+	{
+	  hw_find_integer_array_property (me, "voltage", i, &ival);
+	  cfi->query.voltages[i] = ival;
+	}
+    }
+
+  /* Extract optional timeouts.  */
+  if (hw_find_property (me, "timeout"))
+    {
+      unsigned num = ARRAY_SIZE (cfi->query.timeouts);
+
+      ret = hw_find_integer_array_property (me, "timeout", 0, &ival);
+      if (ret > num)
+	hw_abort (me, "\"timeout\" may have only %u arguments", num);
+
+      for (i = 0; i < ret; ++i)
+	{
+	  hw_find_integer_array_property (me, "timeout", i, &ival);
+	  cfi->query.timeouts[i] = ival;
+	}
+    }
+
+  /* Extract optional file.  */
+  if (hw_find_property (me, "file"))
+    {
+      const char *file;
+
+      ret = hw_find_string_array_property (me, "file", 0, &file);
+      if (ret > 2)
+	hw_abort (me, "\"file\" may take only one argument");
+      if (ret == 2)
+	{
+	  const char *writable;
+
+	  hw_find_string_array_property (me, "file", 1, &writable);
+	  fd_writable = !strcmp (writable, "rw");
+	}
+
+      fd = open (file, fd_writable ? O_RDWR : O_RDONLY);
+      if (fd < 0)
+	hw_abort (me, "unable to read file `%s': %s", file, strerror (errno));
+    }
+  else
+    fd = -1;
+
+  /* Figure out where our initial flash data is coming from.  */
+#ifdef HAVE_MMAP
+  if (fd != -1 && fd_writable)
+    {
+      posix_fallocate (fd, 0, cfi->dev_size);
+
+      cfi->mmap = mmap (NULL, cfi->dev_size,
+			PROT_READ | (fd_writable ? PROT_WRITE : 0),
+			MAP_SHARED, fd, 0);
+
+      if (cfi->mmap == MAP_FAILED)
+	cfi->mmap = NULL;
+      else
+	cfi->data = cfi->mmap;
+    }
+#endif
+  if (!cfi->data)
+    {
+      ssize_t read_len;
+
+      cfi->data = HW_NALLOC (me, unsigned char, cfi->dev_size);
+      if (fd != -1)
+	read_len = read (fd, cfi->data, cfi->dev_size);
+      else
+	read_len = 0;
+      memset (cfi->data, 0xff, cfi->dev_size - read_len);
+    }
+  close (fd);
+}
+
+static void
+cfi_finish (struct hw *me)
+{
+  struct cfi *cfi;
+
+  cfi = HW_ZALLOC (me, struct cfi);
+
+  set_hw_data (me, cfi);
+  set_hw_io_read_buffer (me, cfi_io_read_buffer);
+  set_hw_io_write_buffer (me, cfi_io_write_buffer);
+  set_hw_delete (me, cfi_delete_callback);
+
+  attach_cfi_regs (me, cfi);
+
+  /* Initialize the CFI.  */
+  cfi->state = CFI_STATE_READ;
+  memcpy (cfi->query.qry, "QRY", 3);
+  cfi->cmdset->setup (me, cfi);
+}
+
+const struct hw_descriptor dv_cfi_descriptor[] = {
+  {"cfi", cfi_finish,},
+  {NULL, NULL},
+};
diff --git a/sim/common/dv-cfi.h b/sim/common/dv-cfi.h
new file mode 100644
index 0000000..bd2db2d
--- /dev/null
+++ b/sim/common/dv-cfi.h
@@ -0,0 +1,60 @@
+/* Common Flash Memory Interface (CFI) model.
+
+   Copyright (C) 2010 Free Software Foundation, Inc.
+   Contributed by Analog Devices, Inc.
+
+   This file is part of simulators.
+
+   This program is free software; you can redistribute it and/or modify
+   it under the terms of the GNU General Public License as published by
+   the Free Software Foundation; either version 3 of the License, or
+   (at your option) any later version.
+
+   This program is distributed in the hope that it will be useful,
+   but WITHOUT ANY WARRANTY; without even the implied warranty of
+   MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+   GNU General Public License for more details.
+
+   You should have received a copy of the GNU General Public License
+   along with this program.  If not, see <http://www.gnu.org/licenses/>.  */
+
+#ifndef DV_CFI_H
+#define DV_CFI_H
+
+/* CFI standard.  */
+#define CFI_CMD_CFI_QUERY		0x98
+#define CFI_ADDR_CFI_QUERY_START	0x55
+#define CFI_ADDR_CFI_QUERY_RESULT	0x10
+
+#define CFI_CMD_READ			0xFF
+#define CFI_CMD_RESET			0xF0
+#define CFI_CMD_READ_ID			0x90
+
+/* Intel specific.  */
+#define CFI_CMDSET_INTEL		0x0001
+#define INTEL_CMD_STATUS_CLEAR		0x50
+#define INTEL_CMD_STATUS_READ		0x70
+#define INTEL_CMD_WRITE			0x40
+#define INTEL_CMD_WRITE_ALT		0x10
+#define INTEL_CMD_WRITE_BUFFER		0xE8
+#define INTEL_CMD_WRITE_BUFFER_CONFIRM	0xD0
+#define INTEL_CMD_LOCK_SETUP		0x60
+#define INTEL_CMD_LOCK_BLOCK		0x01
+#define INTEL_CMD_UNLOCK_BLOCK		0xD0
+#define INTEL_CMD_LOCK_DOWN_BLOCK	0x2F
+#define INTEL_CMD_ERASE_BLOCK		0x20
+#define INTEL_CMD_ERASE_CONFIRM		0xD0
+
+/* Intel Status Register bits.  */
+#define INTEL_SR_BWS		(1 << 0)	/* BEFP Write.  */
+#define INTEL_SR_BLS		(1 << 1)	/* Block Locked.  */
+#define INTEL_SR_PSS		(1 << 2)	/* Program Suspend.  */
+#define INTEL_SR_VPPS		(1 << 3)	/* Vpp.  */
+#define INTEL_SR_PS		(1 << 4)	/* Program.  */
+#define INTEL_SR_ES		(1 << 5)	/* Erase.  */
+#define INTEL_SR_ESS		(1 << 6)	/* Erase Suspend.  */
+#define INTEL_SR_DWS		(1 << 7)	/* Device Write.  */
+
+#define INTEL_ID_MANU		0x89
+
+#endif
-- 
1.7.3.1

Re: [PATCH] sim: cfi: new flash device simulation

[Mike Frysinger]

[-- Attachment #1: Type: Text/Plain, Size: 392 bytes --]

On Thursday, December 30, 2010 18:06:54 Mike Frysinger wrote:
> This simulates a CFI flash.  Its pretty configurable via the device
> tree.  For now, only basic read/write/erase operations are supported
> for the Intel command set, but it's easy enough to extend support.
> It's certainly enough to trick Das U-Boot into using it for probing,
> reading, writing, and erasing.

ping ...
-mike

[-- Attachment #2: This is a digitally signed message part. --]
[-- Type: application/pgp-signature, Size: 836 bytes --]

Re: [PATCH] sim: cfi: new flash device simulation

[Mike Frysinger]

[-- Attachment #1: Type: Text/Plain, Size: 492 bytes --]

On Monday, February 07, 2011 01:10:49 Mike Frysinger wrote:
> On Thursday, December 30, 2010 18:06:54 Mike Frysinger wrote:
> > This simulates a CFI flash.  Its pretty configurable via the device
> > tree.  For now, only basic read/write/erase operations are supported
> > for the Intel command set, but it's easy enough to extend support.
> > It's certainly enough to trick Das U-Boot into using it for probing,
> > reading, writing, and erasing.
> 
> ping ...

any love ?
-mike

[-- Attachment #2: This is a digitally signed message part. --]
[-- Type: application/pgp-signature, Size: 836 bytes --]

[PATCH v2] sim: cfi: new flash device simulation

[Mike Frysinger]

This simulates a CFI flash.  Its pretty configurable via the device
tree.  For now, only basic read/write/erase operations are supported
for the Intel command set, but it's easy enough to extend support.
It's certainly enough to trick Das U-Boot into using it for probing,
reading, writing, and erasing.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

2010-12-30  Mike Frysinger  <vapier@gentoo.org>

	* aclocal.m4 (SIM_AC_OPTION_HARDWARE): Add cfi to default list.
	* Make-common.in (dv-cfi.o): New rule.
	* dv-cfi.c, dv-cfi.h: New files.
---
v2
	- missed an ifdef check in the munmap cleanup path that broke Windows builds

 sim/common/Make-common.in |    3 +
 sim/common/aclocal.m4     |    2 +-
 sim/common/dv-cfi.c       |  706 +++++++++++++++++++++++++++++++++++++++++++++
 sim/common/dv-cfi.h       |   60 ++++
 4 files changed, 770 insertions(+), 1 deletions(-)
 create mode 100644 sim/common/dv-cfi.c
 create mode 100644 sim/common/dv-cfi.h

diff --git a/sim/common/Make-common.in b/sim/common/Make-common.in
index 2f0c807..42e3192 100644
--- a/sim/common/Make-common.in
+++ b/sim/common/Make-common.in
@@ -579,6 +579,9 @@ hw-tree.o: $(srccom)/hw-tree.c $(hw_main_headers) $(hw-tree_h)
 
 # Devices.
 
+dv-cfi.o: $(srccom)/dv-cfi.c $(hw_main_headers) $(sim_main_headers)
+	$(CC) -c $(srccom)/dv-cfi.c $(ALL_CFLAGS)
+
 dv-core.o: $(srccom)/dv-core.c $(hw_main_headers) $(sim_main_headers)
 	$(CC) -c $(srccom)/dv-core.c $(ALL_CFLAGS)
 
diff --git a/sim/common/aclocal.m4 b/sim/common/aclocal.m4
index bda20ce..cec0155 100644
--- a/sim/common/aclocal.m4
+++ b/sim/common/aclocal.m4
@@ -573,7 +573,7 @@ fi
 if test "[$2]"; then
   hardware="[$2]"
 else
-  hardware="core pal glue"
+  hardware="cfi core pal glue"
 fi
 hardware="$hardware [$3]"
 sim_hw_cflags="-DWITH_HW=1"
diff --git a/sim/common/dv-cfi.c b/sim/common/dv-cfi.c
new file mode 100644
index 0000000..2b12086
--- /dev/null
+++ b/sim/common/dv-cfi.c
@@ -0,0 +1,706 @@
+/* Common Flash Memory Interface (CFI) model.
+   http://www.spansion.com/Support/AppNotes/CFI_Spec_AN_03.pdf
+   http://www.spansion.com/Support/AppNotes/cfi_100_20011201.pdf
+
+   Copyright (C) 2010 Free Software Foundation, Inc.
+   Contributed by Analog Devices, Inc.
+
+   This file is part of simulators.
+
+   This program is free software; you can redistribute it and/or modify
+   it under the terms of the GNU General Public License as published by
+   the Free Software Foundation; either version 3 of the License, or
+   (at your option) any later version.
+
+   This program is distributed in the hope that it will be useful,
+   but WITHOUT ANY WARRANTY; without even the implied warranty of
+   MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+   GNU General Public License for more details.
+
+   You should have received a copy of the GNU General Public License
+   along with this program.  If not, see <http://www.gnu.org/licenses/>.  */
+
+/* TODO: support vendor query tables.  */
+
+#include "cconfig.h"
+
+#include <math.h>
+#include <errno.h>
+#include <fcntl.h>
+#include <unistd.h>
+#ifdef HAVE_SYS_MMAN_H
+#include <sys/mman.h>
+#endif
+
+#include "sim-main.h"
+#include "devices.h"
+#include "dv-cfi.h"
+
+enum cfi_state
+{
+  CFI_STATE_READ,
+  CFI_STATE_READ_ID,
+  CFI_STATE_CFI_QUERY,
+  CFI_STATE_PROTECT,
+  CFI_STATE_STATUS,
+  CFI_STATE_ERASE,
+  CFI_STATE_WRITE,
+  CFI_STATE_WRITE_BUFFER,
+  CFI_STATE_WRITE_BUFFER_CONFIRM,
+};
+
+struct cfi_query
+{
+  unsigned char qry[3];
+  unsigned char p_id[2];
+  unsigned char p_adr[2];
+  unsigned char a_id[2];
+  unsigned char a_adr[2];
+  union {
+    unsigned char voltages[4];
+    struct {
+      unsigned char vcc_min;
+      unsigned char vcc_max;
+      unsigned char vpp_min;
+      unsigned char vpp_max;
+    };
+  };
+  union {
+    unsigned char timeouts[8];
+    struct {
+      unsigned char timeout_typ_unit_write;
+      unsigned char timeout_typ_buf_write;
+      unsigned char timeout_typ_block_erase;
+      unsigned char timeout_typ_chip_erase;
+      unsigned char timeout_max_unit_write;
+      unsigned char timeout_max_buf_write;
+      unsigned char timeout_max_block_erase;
+      unsigned char timeout_max_chip_erase;
+    };
+  };
+  unsigned char dev_size;
+  unsigned char iface_desc[2];
+  unsigned char max_buf_write_len[2];
+  unsigned char num_erase_regions;
+  /*unsigned char erase_region_info;*/
+};
+
+struct cfi_erase_region
+{
+  unsigned blocks;
+  unsigned size;
+  unsigned start;
+  unsigned end;
+};
+
+struct cfi;
+
+struct cfi_cmdset
+{
+  unsigned id;
+  void (*setup) (struct hw *me, struct cfi *cfi);
+  bool (*write) (struct hw *me, struct cfi *cfi, const void *source,
+		 unsigned offset, unsigned value, unsigned nr_bytes);
+  bool (*read) (struct hw *me, struct cfi *cfi, void *dest,
+		unsigned offset, unsigned shifted_offset, unsigned nr_bytes);
+};
+
+struct cfi
+{
+  unsigned width, dev_size, status;
+  enum cfi_state state;
+  unsigned char *data, *mmap;
+
+  struct cfi_query query;
+  const struct cfi_cmdset *cmdset;
+
+  unsigned char *erase_region_info;
+  struct cfi_erase_region *erase_regions;
+};
+
+static const char * const state_names[] = {
+  "READ", "READ_ID", "CFI_QUERY", "PROTECT", "STATUS", "ERASE", "WRITE",
+  "WRITE_BUFFER", "WRITE_BUFFER_CONFIRM",
+};
+\f
+static void
+cfi_erase_block (struct hw *me, struct cfi *cfi, unsigned offset)
+{
+  unsigned i;
+  struct cfi_erase_region *region;
+
+  /* If no erase regions, then we can only do whole chip erase.  */
+  /* XXX: Is this within spec ?  Or must there always be at least one ?  */
+  if (!cfi->query.num_erase_regions)
+    memset (cfi->data, 0xff, cfi->dev_size);
+
+  for (i = 0; i < cfi->query.num_erase_regions; ++i)
+    {
+      region = &cfi->erase_regions[i];
+
+      if (offset >= region->end)
+	continue;
+
+      /* XXX: Does spec require the erase addr to be erase block aligned ?
+	      Maybe this is check is overly cautious ...  */
+      offset &= ~(region->size - 1);
+      memset (cfi->data + offset, 0xff, region->size);
+      break;
+    }
+}
+
+static unsigned
+cfi_unshift_addr (struct cfi *cfi, unsigned addr)
+{
+  switch (cfi->width)
+    {
+    case 4: addr >>= 1;
+    case 2: addr >>= 1;
+    }
+  return addr;
+}
+
+static void
+cfi_encode_16bit (unsigned char *data, unsigned num)
+{
+  /* CFI is little endian.  */
+  data[0] = num;
+  data[1] = num >> 8;
+}
+\f
+static bool
+cmdset_intel_write (struct hw *me, struct cfi *cfi, const void *source,
+		    unsigned offset, unsigned value, unsigned nr_bytes)
+{
+  switch (cfi->state)
+    {
+    case CFI_STATE_READ:
+    case CFI_STATE_READ_ID:
+      switch (value)
+	{
+	case INTEL_CMD_ERASE_BLOCK:
+	  cfi->state = CFI_STATE_ERASE;
+	  break;
+	case INTEL_CMD_WRITE:
+	case INTEL_CMD_WRITE_ALT:
+	  cfi->state = CFI_STATE_WRITE;
+	  break;
+	case INTEL_CMD_STATUS_CLEAR:
+	  cfi->status = INTEL_SR_DWS;
+	  break;
+	case INTEL_CMD_LOCK_SETUP:
+	  cfi->state = CFI_STATE_PROTECT;
+	  break;
+	default:
+	  return false;
+	}
+      break;
+
+    case CFI_STATE_ERASE:
+      if (value == INTEL_CMD_ERASE_CONFIRM)
+	{
+	  cfi_erase_block (me, cfi, offset);
+	  cfi->status &= ~(INTEL_SR_PS | INTEL_SR_ES);
+	}
+      else
+	cfi->status |= INTEL_SR_PS | INTEL_SR_ES;
+      cfi->state = CFI_STATE_STATUS;
+      break;
+
+    case CFI_STATE_PROTECT:
+      switch (value)
+	{
+	case INTEL_CMD_LOCK_BLOCK:
+	case INTEL_CMD_UNLOCK_BLOCK:
+	case INTEL_CMD_LOCK_DOWN_BLOCK:
+	  /* XXX: Handle the command.  */
+	  break;
+	default:
+	  /* Kick out.  */
+	  cfi->status |= INTEL_SR_PS | INTEL_SR_ES;
+	  break;
+	}
+      cfi->state = CFI_STATE_STATUS;
+      break;
+
+    default:
+      return false;
+    }
+
+  return true;
+}
+
+static bool
+cmdset_intel_read (struct hw *me, struct cfi *cfi, void *dest,
+		   unsigned offset, unsigned shifted_offset, unsigned nr_bytes)
+{
+  unsigned char *sdest = dest;
+
+  switch (cfi->state)
+    {
+    case CFI_STATE_STATUS:
+    case CFI_STATE_ERASE:
+      *sdest = cfi->status;
+      break;
+
+    case CFI_STATE_READ_ID:
+      switch (shifted_offset & 0x1ff)
+	{
+	case 0x00:	/* Manufacturer Code.  */
+	  cfi_encode_16bit (dest, INTEL_ID_MANU);
+	  break;
+	case 0x01:	/* Device ID Code.  */
+	  /* XXX: Push to device tree ?  */
+	  cfi_encode_16bit (dest, 0xad);
+	  break;
+	case 0x02:	/* Block lock state.  */
+	  /* XXX: This is per-block ...  */
+	  *sdest = 0x00;
+	  break;
+	case 0x05:	/* Read Configuration Register.  */
+	  cfi_encode_16bit (dest, (1 << 15));
+	  break;
+	default:
+	  return false;
+	}
+      break;
+
+    default:
+      return false;
+    }
+
+  return true;
+}
+
+static void
+cmdset_intel_setup (struct hw *me, struct cfi *cfi)
+{
+  cfi->status = INTEL_SR_DWS;
+}
+
+static const struct cfi_cmdset cfi_cmdset_intel = {
+  CFI_CMDSET_INTEL, cmdset_intel_setup, cmdset_intel_write, cmdset_intel_read,
+};
+
+static const struct cfi_cmdset * const cfi_cmdsets[] = {
+  &cfi_cmdset_intel,
+};
+\f
+static unsigned
+cfi_io_write_buffer (struct hw *me, const void *source, int space,
+		     address_word addr, unsigned nr_bytes)
+{
+  struct cfi *cfi = hw_data (me);
+  const unsigned char *ssource = source;
+  enum cfi_state old_state;
+  unsigned offset, shifted_offset, value;
+
+  offset = addr & (cfi->dev_size - 1);
+  shifted_offset = cfi_unshift_addr (cfi, offset);
+
+  if (cfi->width != nr_bytes)
+    {
+      HW_TRACE ((me, "write 0x%08lx length %u does not match flash width %u",
+		 (unsigned long) addr, nr_bytes, cfi->width));
+      return nr_bytes;
+    }
+
+  if (cfi->state == CFI_STATE_WRITE)
+    {
+      /* NOR flash can only go from 1 to 0.  */
+      unsigned i;
+
+      HW_TRACE ((me, "program %#x length %u", offset, nr_bytes));
+
+      for (i = 0; i < nr_bytes; ++i)
+	cfi->data[offset + i] &= ssource[i];
+
+      cfi->state = CFI_STATE_STATUS;
+
+      return nr_bytes;
+    }
+
+  value = ssource[0];
+
+  old_state = cfi->state;
+
+  if (value == CFI_CMD_READ || value == CFI_CMD_RESET)
+    {
+      cfi->state = CFI_STATE_READ;
+      goto done;
+    }
+
+  switch (cfi->state)
+    {
+    case CFI_STATE_READ:
+    case CFI_STATE_READ_ID:
+      if (value == CFI_CMD_CFI_QUERY)
+	{
+	  if (shifted_offset == CFI_ADDR_CFI_QUERY_START)
+	    cfi->state = CFI_STATE_CFI_QUERY;
+	  goto done;
+	}
+
+      if (value == CFI_CMD_READ_ID)
+	{
+	  cfi->state = CFI_STATE_READ_ID;
+	  goto done;
+	}
+
+      /* Fall through.  */
+
+    default:
+      if (!cfi->cmdset->write (me, cfi, source, offset, value, nr_bytes))
+	HW_TRACE ((me, "unhandled command %#x at %#x", value, offset));
+      break;
+    }
+
+ done:
+  HW_TRACE ((me, "write 0x%08lx command {%#x,%#x,%#x,%#x}; state %s -> %s",
+	     (unsigned long) addr, ssource[0],
+	     nr_bytes > 1 ? ssource[1] : 0,
+	     nr_bytes > 2 ? ssource[2] : 0,
+	     nr_bytes > 3 ? ssource[3] : 0,
+	     state_names[old_state], state_names[cfi->state]));
+
+  return nr_bytes;
+}
+
+static unsigned
+cfi_io_read_buffer (struct hw *me, void *dest, int space,
+		    address_word addr, unsigned nr_bytes)
+{
+  struct cfi *cfi = hw_data (me);
+  unsigned char *sdest = dest;
+  unsigned offset, shifted_offset;
+
+  offset = addr & (cfi->dev_size - 1);
+  shifted_offset = cfi_unshift_addr (cfi, offset);
+
+  /* XXX: Is this OK to enforce ?  */
+#if 0
+  if (cfi->state != CFI_STATE_READ && cfi->width != nr_bytes)
+    {
+      HW_TRACE ((me, "read 0x%08lx length %u does not match flash width %u",
+		 (unsigned long) addr, nr_bytes, cfi->width));
+      return nr_bytes;
+    }
+#endif
+
+  HW_TRACE ((me, "%s read 0x%08lx length %u",
+	     state_names[cfi->state], (unsigned long) addr, nr_bytes));
+
+  switch (cfi->state)
+    {
+    case CFI_STATE_READ:
+      memcpy (dest, cfi->data + offset, nr_bytes);
+      break;
+
+    case CFI_STATE_CFI_QUERY:
+      if (shifted_offset >= CFI_ADDR_CFI_QUERY_RESULT &&
+	  shifted_offset < CFI_ADDR_CFI_QUERY_RESULT + sizeof (cfi->query) +
+		     (cfi->query.num_erase_regions * 4))
+	{
+	  unsigned char *qry;
+
+	  shifted_offset -= CFI_ADDR_CFI_QUERY_RESULT;
+	  if (shifted_offset >= sizeof (cfi->query))
+	    {
+	      qry = cfi->erase_region_info;
+	      shifted_offset -= sizeof (cfi->query);
+	    }
+	  else
+	    qry = (void *) &cfi->query;
+
+	  sdest[0] = qry[shifted_offset];
+	  memset (sdest + 1, 0, nr_bytes - 1);
+
+	  break;
+	}
+
+    default:
+      if (!cfi->cmdset->read (me, cfi, dest, offset, shifted_offset, nr_bytes))
+	HW_TRACE ((me, "unhandled state %s", state_names[cfi->state]));
+      break;
+    }
+
+  return nr_bytes;
+}
+
+static void
+cfi_delete_callback (struct hw *me)
+{
+#ifdef HAVE_MMAP
+  struct cfi *cfi = hw_data (me);
+
+  if (cfi->mmap)
+    munmap (cfi->mmap, cfi->dev_size);
+#endif
+}
+
+static void
+cfi_add_erase_region (struct hw *me, struct cfi *cfi,
+		      unsigned blocks, unsigned size)
+{
+  unsigned num_regions = cfi->query.num_erase_regions;
+  struct cfi_erase_region *region;
+  unsigned char *qry_region;
+
+  /* Store for our own usage.  */
+  region = &cfi->erase_regions[num_regions];
+  region->blocks = blocks;
+  region->size = size;
+  if (num_regions == 0)
+    region->start = 0;
+  else
+    region->start = region[-1].end;
+  region->end = region->start + (blocks * size);
+
+  /* Regions are 4 bytes long.  */
+  qry_region = cfi->erase_region_info + 4 * num_regions;
+
+  /* [0][1] = number erase blocks - 1 */
+  if (blocks > 0xffff + 1)
+    hw_abort (me, "erase blocks %u too big to fit into region info", blocks);
+  cfi_encode_16bit (&qry_region[0], blocks - 1);
+
+  /* [2][3] = block size / 256 bytes */
+  if (size > 0xffff * 256)
+    hw_abort (me, "erase size %u too big to fit into region info", size);
+  cfi_encode_16bit (&qry_region[2], size / 256);
+
+  /* Yet another region.  */
+  cfi->query.num_erase_regions = num_regions + 1;
+}
+
+/* Device tree options:
+     Required:
+       .../reg <addr> <len>
+       .../cmdset <primary; integer> [alt; integer]
+     Optional:
+       .../size <device size (must be pow of 2)>
+       .../width <8|16|32>
+       .../write_size <integer (must be pow of 2)>
+       .../erase_regions <number blocks> <block size> \
+                         [<number blocks> <block size> ...]
+       .../voltage <vcc min> <vcc max> <vpp min> <vpp max>
+       .../timeouts <typ unit write>  <typ buf write>  \
+                    <typ block erase> <typ chip erase> \
+                    <max unit write>  <max buf write>  \
+                    <max block erase> <max chip erase>
+       .../file <file> [ro|rw]
+     Defaults:
+       size: <len> from "reg"
+       width: 8
+       write_size: 0 (not supported)
+       erase_region: 1 (can only erase whole chip)
+       voltage: 0.0V (for all)
+       timeouts: typ: 1µs, not supported, 1ms, not supported
+                 max: 1µs, 1ms, 1ms, not supported
+
+  TODO: Verify user args are valid (e.g. voltage is 8 bits).  */
+static void
+attach_cfi_regs (struct hw *me, struct cfi *cfi)
+{
+  address_word attach_address;
+  int attach_space;
+  unsigned attach_size;
+  reg_property_spec reg;
+  bool fd_writable;
+  int i, ret, fd;
+  signed_cell ival;
+
+  if (hw_find_property (me, "reg") == NULL)
+    hw_abort (me, "Missing \"reg\" property");
+  if (hw_find_property (me, "cmdset") == NULL)
+    hw_abort (me, "Missing \"cmdset\" property");
+
+  if (!hw_find_reg_array_property (me, "reg", 0, &reg))
+    hw_abort (me, "\"reg\" property must contain three addr/size entries");
+
+  hw_unit_address_to_attach_address (hw_parent (me),
+				     &reg.address,
+				     &attach_space, &attach_address, me);
+  hw_unit_size_to_attach_size (hw_parent (me), &reg.size, &attach_size, me);
+
+  hw_attach_address (hw_parent (me),
+		     0, attach_space, attach_address, attach_size, me);
+
+  /* Extract the desired flash command set.  */
+  ret = hw_find_integer_array_property (me, "cmdset", 0, &ival);
+  if (ret != 1 && ret != 2)
+    hw_abort (me, "\"cmdset\" property takes 1 or 2 entries");
+  cfi_encode_16bit (cfi->query.p_id, ival);
+
+  for (i = 0; i < ARRAY_SIZE (cfi_cmdsets); ++i)
+    if (cfi_cmdsets[i]->id == ival)
+      cfi->cmdset = cfi_cmdsets[i];
+  if (cfi->cmdset == NULL)
+    hw_abort (me, "cmdset %u not supported", ival);
+
+  if (ret == 2)
+    {
+      hw_find_integer_array_property (me, "cmdset", 1, &ival);
+      cfi_encode_16bit (cfi->query.a_id, ival);
+    }
+
+  /* Extract the desired device size.  */
+  if (hw_find_property (me, "size"))
+    cfi->dev_size = hw_find_integer_property (me, "size");
+  else
+    cfi->dev_size = attach_size;
+  cfi->query.dev_size = log2 (cfi->dev_size);
+
+  /* Extract the desired flash width.  */
+  if (hw_find_property (me, "width"))
+    {
+      cfi->width = hw_find_integer_property (me, "width");
+      if (cfi->width != 8 && cfi->width != 16 && cfi->width != 32)
+	hw_abort (me, "\"width\" must be 8 or 16 or 32, not %u", cfi->width);
+    }
+  else
+    /* Default to 8 bit.  */
+    cfi->width = 8;
+  /* Turn 8/16/32 into 1/2/4.  */
+  cfi->width /= 8;
+
+  /* Extract optional write buffer size.  */
+  if (hw_find_property (me, "write_size"))
+    {
+      ival = hw_find_integer_property (me, "write_size");
+      cfi_encode_16bit (cfi->query.max_buf_write_len, log2 (ival));
+    }
+
+  /* Extract optional erase regions.  */
+  if (hw_find_property (me, "erase_regions"))
+    {
+      ret = hw_find_integer_array_property (me, "erase_regions", 0, &ival);
+      if (ret % 2)
+	hw_abort (me, "\"erase_regions\" must be specified in sets of 2");
+
+      cfi->erase_region_info = HW_NALLOC (me, unsigned char, ret / 2);
+      cfi->erase_regions = HW_NALLOC (me, struct cfi_erase_region, ret / 2);
+
+      for (i = 0; i < ret; i += 2)
+	{
+	  unsigned blocks, size;
+
+	  hw_find_integer_array_property (me, "erase_regions", i, &ival);
+	  blocks = ival;
+
+	  hw_find_integer_array_property (me, "erase_regions", i + 1, &ival);
+	  size = ival;
+
+	  cfi_add_erase_region (me, cfi, blocks, size);
+	}
+    }
+
+  /* Extract optional voltages.  */
+  if (hw_find_property (me, "voltage"))
+    {
+      unsigned num = ARRAY_SIZE (cfi->query.voltages);
+
+      ret = hw_find_integer_array_property (me, "voltage", 0, &ival);
+      if (ret > num)
+	hw_abort (me, "\"voltage\" may have only %u arguments", num);
+
+      for (i = 0; i < ret; ++i)
+	{
+	  hw_find_integer_array_property (me, "voltage", i, &ival);
+	  cfi->query.voltages[i] = ival;
+	}
+    }
+
+  /* Extract optional timeouts.  */
+  if (hw_find_property (me, "timeout"))
+    {
+      unsigned num = ARRAY_SIZE (cfi->query.timeouts);
+
+      ret = hw_find_integer_array_property (me, "timeout", 0, &ival);
+      if (ret > num)
+	hw_abort (me, "\"timeout\" may have only %u arguments", num);
+
+      for (i = 0; i < ret; ++i)
+	{
+	  hw_find_integer_array_property (me, "timeout", i, &ival);
+	  cfi->query.timeouts[i] = ival;
+	}
+    }
+
+  /* Extract optional file.  */
+  fd = -1;
+  fd_writable = false;
+  if (hw_find_property (me, "file"))
+    {
+      const char *file;
+
+      ret = hw_find_string_array_property (me, "file", 0, &file);
+      if (ret > 2)
+	hw_abort (me, "\"file\" may take only one argument");
+      if (ret == 2)
+	{
+	  const char *writable;
+
+	  hw_find_string_array_property (me, "file", 1, &writable);
+	  fd_writable = !strcmp (writable, "rw");
+	}
+
+      fd = open (file, fd_writable ? O_RDWR : O_RDONLY);
+      if (fd < 0)
+	hw_abort (me, "unable to read file `%s': %s", file, strerror (errno));
+    }
+
+  /* Figure out where our initial flash data is coming from.  */
+#ifdef HAVE_MMAP
+  if (fd != -1 && fd_writable)
+    {
+      posix_fallocate (fd, 0, cfi->dev_size);
+
+      cfi->mmap = mmap (NULL, cfi->dev_size,
+			PROT_READ | (fd_writable ? PROT_WRITE : 0),
+			MAP_SHARED, fd, 0);
+
+      if (cfi->mmap == MAP_FAILED)
+	cfi->mmap = NULL;
+      else
+	cfi->data = cfi->mmap;
+    }
+#endif
+  if (!cfi->data)
+    {
+      ssize_t read_len;
+
+      cfi->data = HW_NALLOC (me, unsigned char, cfi->dev_size);
+      if (fd != -1)
+	read_len = read (fd, cfi->data, cfi->dev_size);
+      else
+	read_len = 0;
+      memset (cfi->data, 0xff, cfi->dev_size - read_len);
+    }
+  close (fd);
+}
+
+static void
+cfi_finish (struct hw *me)
+{
+  struct cfi *cfi;
+
+  cfi = HW_ZALLOC (me, struct cfi);
+
+  set_hw_data (me, cfi);
+  set_hw_io_read_buffer (me, cfi_io_read_buffer);
+  set_hw_io_write_buffer (me, cfi_io_write_buffer);
+  set_hw_delete (me, cfi_delete_callback);
+
+  attach_cfi_regs (me, cfi);
+
+  /* Initialize the CFI.  */
+  cfi->state = CFI_STATE_READ;
+  memcpy (cfi->query.qry, "QRY", 3);
+  cfi->cmdset->setup (me, cfi);
+}
+
+const struct hw_descriptor dv_cfi_descriptor[] = {
+  {"cfi", cfi_finish,},
+  {NULL, NULL},
+};
diff --git a/sim/common/dv-cfi.h b/sim/common/dv-cfi.h
new file mode 100644
index 0000000..bd2db2d
--- /dev/null
+++ b/sim/common/dv-cfi.h
@@ -0,0 +1,60 @@
+/* Common Flash Memory Interface (CFI) model.
+
+   Copyright (C) 2010 Free Software Foundation, Inc.
+   Contributed by Analog Devices, Inc.
+
+   This file is part of simulators.
+
+   This program is free software; you can redistribute it and/or modify
+   it under the terms of the GNU General Public License as published by
+   the Free Software Foundation; either version 3 of the License, or
+   (at your option) any later version.
+
+   This program is distributed in the hope that it will be useful,
+   but WITHOUT ANY WARRANTY; without even the implied warranty of
+   MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+   GNU General Public License for more details.
+
+   You should have received a copy of the GNU General Public License
+   along with this program.  If not, see <http://www.gnu.org/licenses/>.  */
+
+#ifndef DV_CFI_H
+#define DV_CFI_H
+
+/* CFI standard.  */
+#define CFI_CMD_CFI_QUERY		0x98
+#define CFI_ADDR_CFI_QUERY_START	0x55
+#define CFI_ADDR_CFI_QUERY_RESULT	0x10
+
+#define CFI_CMD_READ			0xFF
+#define CFI_CMD_RESET			0xF0
+#define CFI_CMD_READ_ID			0x90
+
+/* Intel specific.  */
+#define CFI_CMDSET_INTEL		0x0001
+#define INTEL_CMD_STATUS_CLEAR		0x50
+#define INTEL_CMD_STATUS_READ		0x70
+#define INTEL_CMD_WRITE			0x40
+#define INTEL_CMD_WRITE_ALT		0x10
+#define INTEL_CMD_WRITE_BUFFER		0xE8
+#define INTEL_CMD_WRITE_BUFFER_CONFIRM	0xD0
+#define INTEL_CMD_LOCK_SETUP		0x60
+#define INTEL_CMD_LOCK_BLOCK		0x01
+#define INTEL_CMD_UNLOCK_BLOCK		0xD0
+#define INTEL_CMD_LOCK_DOWN_BLOCK	0x2F
+#define INTEL_CMD_ERASE_BLOCK		0x20
+#define INTEL_CMD_ERASE_CONFIRM		0xD0
+
+/* Intel Status Register bits.  */
+#define INTEL_SR_BWS		(1 << 0)	/* BEFP Write.  */
+#define INTEL_SR_BLS		(1 << 1)	/* Block Locked.  */
+#define INTEL_SR_PSS		(1 << 2)	/* Program Suspend.  */
+#define INTEL_SR_VPPS		(1 << 3)	/* Vpp.  */
+#define INTEL_SR_PS		(1 << 4)	/* Program.  */
+#define INTEL_SR_ES		(1 << 5)	/* Erase.  */
+#define INTEL_SR_ESS		(1 << 6)	/* Erase Suspend.  */
+#define INTEL_SR_DWS		(1 << 7)	/* Device Write.  */
+
+#define INTEL_ID_MANU		0x89
+
+#endif
-- 
1.7.4.1

Re: [PATCH v2] sim: cfi: new flash device simulation

[Joel Brobecker]

> 2010-12-30  Mike Frysinger  <vapier@gentoo.org>
> 
> 	* aclocal.m4 (SIM_AC_OPTION_HARDWARE): Add cfi to default list.
> 	* Make-common.in (dv-cfi.o): New rule.
> 	* dv-cfi.c, dv-cfi.h: New files.

Almost OK.

There are just a few minor comments:
  - opening curly brace in struct union declarations should be on
    the next line
  - We're not fond of commented out code.  You could replace it by
    a comment if useful.
  - I realize that this is a large-ish job, but it would be nice to
    have all types and routines documented.  Generally, it's even
    preferable to document the fields in the struct/union types,
    but a small description of the type will be a good start for now.
  - I think that this deserves a NEWS entry
  - And I think that we should add some documentation in the GDB
    Manual.  The simulator section is almost non-existent in the
    current manual, but if we could start defining a general structure,
    even if they are empty, and document this new feature in that
    structure, at least we won't make things worse.

-- 
Joel

Re: [PATCH v2] sim: cfi: new flash device simulation

[Mike Frysinger]

On Thu, Mar 24, 2011 at 11:14 AM, Joel Brobecker wrote:
> There are just a few minor comments:
>  - opening curly brace in struct union declarations should be on
>    the next line

some habits die hard ;).  especially when i looked at sim/common/ and
they all use the style i did.

>  - We're not fond of commented out code.  You could replace it by
>    a comment if useful.

only place i see this is top of cfi_io_read_buffer() where a minor
check is #ifdef-ed out.

i guess i could change it to something like:
  /* XXX: Should we require read's to have cfi->width == nr_bytes ?  */

obviously i prefer the existing #if 0 approach since it has been tested ;)

>  - I realize that this is a large-ish job, but it would be nice to
>    have all types and routines documented.  Generally, it's even
>    preferable to document the fields in the struct/union types,
>    but a small description of the type will be a good start for now.

the fields should match 1:1 to the CFI spec, but i can sprinkle some
comments about and see what happens.  i spent the most time on the
comment that people who want to *use* the code need.  after all,
people should only need to care about the device tree format and not
know any of the internals.

>  - I think that this deserves a NEWS entry

in gdb/NEWS i guess

>  - And I think that we should add some documentation in the GDB
>    Manual.  The simulator section is almost non-existent in the
>    current manual, but if we could start defining a general structure,
>    even if they are empty, and document this new feature in that
>    structure, at least we won't make things worse.

yeah, i think you mentioned this before
-mike

[PATCH v3] sim: cfi: new flash device simulation

[Mike Frysinger]

This simulates a CFI flash.  Its pretty configurable via the device
tree.  For now, only basic read/write/erase operations are supported
for the Intel command set, but it's easy enough to extend support.
It's certainly enough to trick Das U-Boot into using it for probing,
reading, writing, and erasing.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

gdb/:
2011-03-24  Mike Frysinger  <vapier@gentoo.org>

	* NEWS: Mention new cfi device simulation.

sim/common/:
2011-03-24  Mike Frysinger  <vapier@gentoo.org>

	* aclocal.m4 (SIM_AC_OPTION_HARDWARE): Add cfi to default list.
	* Make-common.in (dv-cfi.o): New rule.
	* dv-cfi.c, dv-cfi.h: New files.
---
v3
	- fix style issues
	- add comments all over
	- add NEWS entry

 gdb/NEWS                  |    2 +
 sim/common/Make-common.in |    3 +
 sim/common/aclocal.m4     |    2 +-
 sim/common/dv-cfi.c       |  780 +++++++++++++++++++++++++++++++++++++++++++++
 sim/common/dv-cfi.h       |   60 ++++
 5 files changed, 846 insertions(+), 1 deletions(-)
 create mode 100644 sim/common/dv-cfi.c
 create mode 100644 sim/common/dv-cfi.h

diff --git a/gdb/NEWS b/gdb/NEWS
index 2288497..a09395c 100644
--- a/gdb/NEWS
+++ b/gdb/NEWS
@@ -182,6 +182,8 @@ Analog Devices, Inc. Blackfin Processor	bfin-*
 
   ** The --map-info flag lists all known core mappings.
 
+  ** CFI flashes may be simulated via the "cfi" device.
+
 *** Changes in GDB 7.2
 
 * Shared library support for remote targets by default
diff --git a/sim/common/Make-common.in b/sim/common/Make-common.in
index 2f0c807..42e3192 100644
--- a/sim/common/Make-common.in
+++ b/sim/common/Make-common.in
@@ -579,6 +579,9 @@ hw-tree.o: $(srccom)/hw-tree.c $(hw_main_headers) $(hw-tree_h)
 
 # Devices.
 
+dv-cfi.o: $(srccom)/dv-cfi.c $(hw_main_headers) $(sim_main_headers)
+	$(CC) -c $(srccom)/dv-cfi.c $(ALL_CFLAGS)
+
 dv-core.o: $(srccom)/dv-core.c $(hw_main_headers) $(sim_main_headers)
 	$(CC) -c $(srccom)/dv-core.c $(ALL_CFLAGS)
 
diff --git a/sim/common/aclocal.m4 b/sim/common/aclocal.m4
index bda20ce..cec0155 100644
--- a/sim/common/aclocal.m4
+++ b/sim/common/aclocal.m4
@@ -573,7 +573,7 @@ fi
 if test "[$2]"; then
   hardware="[$2]"
 else
-  hardware="core pal glue"
+  hardware="cfi core pal glue"
 fi
 hardware="$hardware [$3]"
 sim_hw_cflags="-DWITH_HW=1"
diff --git a/sim/common/dv-cfi.c b/sim/common/dv-cfi.c
new file mode 100644
index 0000000..6121d1b
--- /dev/null
+++ b/sim/common/dv-cfi.c
@@ -0,0 +1,780 @@
+/* Common Flash Memory Interface (CFI) model.
+   http://www.spansion.com/Support/AppNotes/CFI_Spec_AN_03.pdf
+   http://www.spansion.com/Support/AppNotes/cfi_100_20011201.pdf
+
+   Copyright (C) 2010-2011 Free Software Foundation, Inc.
+   Contributed by Analog Devices, Inc.
+
+   This file is part of simulators.
+
+   This program is free software; you can redistribute it and/or modify
+   it under the terms of the GNU General Public License as published by
+   the Free Software Foundation; either version 3 of the License, or
+   (at your option) any later version.
+
+   This program is distributed in the hope that it will be useful,
+   but WITHOUT ANY WARRANTY; without even the implied warranty of
+   MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+   GNU General Public License for more details.
+
+   You should have received a copy of the GNU General Public License
+   along with this program.  If not, see <http://www.gnu.org/licenses/>.  */
+
+/* TODO: support vendor query tables.  */
+
+#include "cconfig.h"
+
+#include <math.h>
+#include <errno.h>
+#include <fcntl.h>
+#include <unistd.h>
+#ifdef HAVE_SYS_MMAN_H
+#include <sys/mman.h>
+#endif
+
+#include "sim-main.h"
+#include "devices.h"
+#include "dv-cfi.h"
+
+/* Flashes are simple state machines, so here we cover all the different states
+   a device might be in at any particular time.  */
+enum cfi_state
+{
+  CFI_STATE_READ,
+  CFI_STATE_READ_ID,
+  CFI_STATE_CFI_QUERY,
+  CFI_STATE_PROTECT,
+  CFI_STATE_STATUS,
+  CFI_STATE_ERASE,
+  CFI_STATE_WRITE,
+  CFI_STATE_WRITE_BUFFER,
+  CFI_STATE_WRITE_BUFFER_CONFIRM,
+};
+
+/* This is the structure that all CFI conforming devices must provided when
+   asked for it.  This allows a single driver to dynamically support different
+   flash geometries without having to hardcode specs.
+
+   If you want to start mucking about here, you should just grab the CFI spec
+   and review that (see top of this file for URIs).  */
+struct cfi_query
+{
+  /* This is always 'Q' 'R' 'Y'.  */
+  unsigned char qry[3];
+  /* Primary vendor ID.  */
+  unsigned char p_id[2];
+  /* Primary query table address.  */
+  unsigned char p_adr[2];
+  /* Alternate vendor ID.  */
+  unsigned char a_id[2];
+  /* Alternate query table address.  */
+  unsigned char a_adr[2];
+  union
+  {
+    /* Voltage levels.  */
+    unsigned char voltages[4];
+    struct
+    {
+      /* Normal min voltage level.  */
+      unsigned char vcc_min;
+      /* Normal max voltage level.  */
+      unsigned char vcc_max;
+      /* Programming min volage level.  */
+      unsigned char vpp_min;
+      /* Programming max volage level.  */
+      unsigned char vpp_max;
+    };
+  };
+  union
+  {
+    /* Operational timeouts.  */
+    unsigned char timeouts[8];
+    struct
+    {
+      /* Typical timeout for writing a single "unit".  */
+      unsigned char timeout_typ_unit_write;
+      /* Typical timeout for writing a single "buffer".  */
+      unsigned char timeout_typ_buf_write;
+      /* Typical timeout for erasing a block.  */
+      unsigned char timeout_typ_block_erase;
+      /* Typical timeout for erasing the chip.  */
+      unsigned char timeout_typ_chip_erase;
+      /* Max timeout for writing a single "unit".  */
+      unsigned char timeout_max_unit_write;
+      /* Max timeout for writing a single "buffer".  */
+      unsigned char timeout_max_buf_write;
+      /* Max timeout for erasing a block.  */
+      unsigned char timeout_max_block_erase;
+      /* Max timeout for erasing the chip.  */
+      unsigned char timeout_max_chip_erase;
+    };
+  };
+  /* Flash size is 2^dev_size bytes.  */
+  unsigned char dev_size;
+  /* Flash device interface description.  */
+  unsigned char iface_desc[2];
+  /* Max length of a single buffer write is 2^max_buf_write_len bytes.  */
+  unsigned char max_buf_write_len[2];
+  /* Number of erase regions.  */
+  unsigned char num_erase_regions;
+  /* The erase regions would now be an array after this point, but since
+     it is dynamic, we'll provide that from "struct cfi" when requested.  */
+  /*unsigned char erase_region_info;*/
+};
+
+/* Flashes may have regions with different erase sizes.  There is one
+   structure per erase region.  */
+struct cfi_erase_region
+{
+  unsigned blocks;
+  unsigned size;
+  unsigned start;
+  unsigned end;
+};
+
+struct cfi;
+
+/* Flashes are accessed via commands -- you write a certain number to a special
+   address to change the flash state and access info other than the data.  Diff
+   companies have implemented their own command set.  This structure abstracts
+   the different command sets so that we can support multiple ones with just a
+   single sim driver.  */
+struct cfi_cmdset
+{
+  unsigned id;
+  void (*setup) (struct hw *me, struct cfi *cfi);
+  bool (*write) (struct hw *me, struct cfi *cfi, const void *source,
+		 unsigned offset, unsigned value, unsigned nr_bytes);
+  bool (*read) (struct hw *me, struct cfi *cfi, void *dest,
+		unsigned offset, unsigned shifted_offset, unsigned nr_bytes);
+};
+
+/* The per-flash state.  Much of this comes from the device tree which people
+   declare themselves.  See top of attach_cfi_regs() for more info.  */
+struct cfi
+{
+  unsigned width, dev_size, status;
+  enum cfi_state state;
+  unsigned char *data, *mmap;
+
+  struct cfi_query query;
+  const struct cfi_cmdset *cmdset;
+
+  unsigned char *erase_region_info;
+  struct cfi_erase_region *erase_regions;
+};
+
+/* Helpful strings which are used with HW_TRACE.  */
+static const char * const state_names[] =
+{
+  "READ", "READ_ID", "CFI_QUERY", "PROTECT", "STATUS", "ERASE", "WRITE",
+  "WRITE_BUFFER", "WRITE_BUFFER_CONFIRM",
+};
+\f
+/* Erase the block specified by the offset into the given CFI flash.  */
+static void
+cfi_erase_block (struct hw *me, struct cfi *cfi, unsigned offset)
+{
+  unsigned i;
+  struct cfi_erase_region *region;
+
+  /* If no erase regions, then we can only do whole chip erase.  */
+  /* XXX: Is this within spec ?  Or must there always be at least one ?  */
+  if (!cfi->query.num_erase_regions)
+    memset (cfi->data, 0xff, cfi->dev_size);
+
+  for (i = 0; i < cfi->query.num_erase_regions; ++i)
+    {
+      region = &cfi->erase_regions[i];
+
+      if (offset >= region->end)
+	continue;
+
+      /* XXX: Does spec require the erase addr to be erase block aligned ?
+	      Maybe this is check is overly cautious ...  */
+      offset &= ~(region->size - 1);
+      memset (cfi->data + offset, 0xff, region->size);
+      break;
+    }
+}
+
+/* Depending on the bus width, addresses might be bit shifted.  This helps
+   us normalize everything without cluttering up the rest of the code.  */
+static unsigned
+cfi_unshift_addr (struct cfi *cfi, unsigned addr)
+{
+  switch (cfi->width)
+    {
+    case 4: addr >>= 1;
+    case 2: addr >>= 1;
+    }
+  return addr;
+}
+
+/* CFI requires all values to be little endian in its structure, so this
+   helper writes a 16bit value into a little endian byte buffer.  */
+static void
+cfi_encode_16bit (unsigned char *data, unsigned num)
+{
+  data[0] = num;
+  data[1] = num >> 8;
+}
+\f
+/* The functions required to implement the Intel command set.  */
+
+static bool
+cmdset_intel_write (struct hw *me, struct cfi *cfi, const void *source,
+		    unsigned offset, unsigned value, unsigned nr_bytes)
+{
+  switch (cfi->state)
+    {
+    case CFI_STATE_READ:
+    case CFI_STATE_READ_ID:
+      switch (value)
+	{
+	case INTEL_CMD_ERASE_BLOCK:
+	  cfi->state = CFI_STATE_ERASE;
+	  break;
+	case INTEL_CMD_WRITE:
+	case INTEL_CMD_WRITE_ALT:
+	  cfi->state = CFI_STATE_WRITE;
+	  break;
+	case INTEL_CMD_STATUS_CLEAR:
+	  cfi->status = INTEL_SR_DWS;
+	  break;
+	case INTEL_CMD_LOCK_SETUP:
+	  cfi->state = CFI_STATE_PROTECT;
+	  break;
+	default:
+	  return false;
+	}
+      break;
+
+    case CFI_STATE_ERASE:
+      if (value == INTEL_CMD_ERASE_CONFIRM)
+	{
+	  cfi_erase_block (me, cfi, offset);
+	  cfi->status &= ~(INTEL_SR_PS | INTEL_SR_ES);
+	}
+      else
+	cfi->status |= INTEL_SR_PS | INTEL_SR_ES;
+      cfi->state = CFI_STATE_STATUS;
+      break;
+
+    case CFI_STATE_PROTECT:
+      switch (value)
+	{
+	case INTEL_CMD_LOCK_BLOCK:
+	case INTEL_CMD_UNLOCK_BLOCK:
+	case INTEL_CMD_LOCK_DOWN_BLOCK:
+	  /* XXX: Handle the command.  */
+	  break;
+	default:
+	  /* Kick out.  */
+	  cfi->status |= INTEL_SR_PS | INTEL_SR_ES;
+	  break;
+	}
+      cfi->state = CFI_STATE_STATUS;
+      break;
+
+    default:
+      return false;
+    }
+
+  return true;
+}
+
+static bool
+cmdset_intel_read (struct hw *me, struct cfi *cfi, void *dest,
+		   unsigned offset, unsigned shifted_offset, unsigned nr_bytes)
+{
+  unsigned char *sdest = dest;
+
+  switch (cfi->state)
+    {
+    case CFI_STATE_STATUS:
+    case CFI_STATE_ERASE:
+      *sdest = cfi->status;
+      break;
+
+    case CFI_STATE_READ_ID:
+      switch (shifted_offset & 0x1ff)
+	{
+	case 0x00:	/* Manufacturer Code.  */
+	  cfi_encode_16bit (dest, INTEL_ID_MANU);
+	  break;
+	case 0x01:	/* Device ID Code.  */
+	  /* XXX: Push to device tree ?  */
+	  cfi_encode_16bit (dest, 0xad);
+	  break;
+	case 0x02:	/* Block lock state.  */
+	  /* XXX: This is per-block ...  */
+	  *sdest = 0x00;
+	  break;
+	case 0x05:	/* Read Configuration Register.  */
+	  cfi_encode_16bit (dest, (1 << 15));
+	  break;
+	default:
+	  return false;
+	}
+      break;
+
+    default:
+      return false;
+    }
+
+  return true;
+}
+
+static void
+cmdset_intel_setup (struct hw *me, struct cfi *cfi)
+{
+  cfi->status = INTEL_SR_DWS;
+}
+
+static const struct cfi_cmdset cfi_cmdset_intel =
+{
+  CFI_CMDSET_INTEL, cmdset_intel_setup, cmdset_intel_write, cmdset_intel_read,
+};
+\f
+/* All of the supported command sets get listed here.  We then walk this
+   array to see if the user requested command set is implemented.  */
+static const struct cfi_cmdset * const cfi_cmdsets[] =
+{
+  &cfi_cmdset_intel,
+};
+\f
+/* All writes to the flash address space come here.  Using the state machine,
+   we figure out what to do with this specific write.  All common code sits
+   here and if there is a request we can't process, we hand it off to the
+   command set-specific write function.  */
+static unsigned
+cfi_io_write_buffer (struct hw *me, const void *source, int space,
+		     address_word addr, unsigned nr_bytes)
+{
+  struct cfi *cfi = hw_data (me);
+  const unsigned char *ssource = source;
+  enum cfi_state old_state;
+  unsigned offset, shifted_offset, value;
+
+  offset = addr & (cfi->dev_size - 1);
+  shifted_offset = cfi_unshift_addr (cfi, offset);
+
+  if (cfi->width != nr_bytes)
+    {
+      HW_TRACE ((me, "write 0x%08lx length %u does not match flash width %u",
+		 (unsigned long) addr, nr_bytes, cfi->width));
+      return nr_bytes;
+    }
+
+  if (cfi->state == CFI_STATE_WRITE)
+    {
+      /* NOR flash can only go from 1 to 0.  */
+      unsigned i;
+
+      HW_TRACE ((me, "program %#x length %u", offset, nr_bytes));
+
+      for (i = 0; i < nr_bytes; ++i)
+	cfi->data[offset + i] &= ssource[i];
+
+      cfi->state = CFI_STATE_STATUS;
+
+      return nr_bytes;
+    }
+
+  value = ssource[0];
+
+  old_state = cfi->state;
+
+  if (value == CFI_CMD_READ || value == CFI_CMD_RESET)
+    {
+      cfi->state = CFI_STATE_READ;
+      goto done;
+    }
+
+  switch (cfi->state)
+    {
+    case CFI_STATE_READ:
+    case CFI_STATE_READ_ID:
+      if (value == CFI_CMD_CFI_QUERY)
+	{
+	  if (shifted_offset == CFI_ADDR_CFI_QUERY_START)
+	    cfi->state = CFI_STATE_CFI_QUERY;
+	  goto done;
+	}
+
+      if (value == CFI_CMD_READ_ID)
+	{
+	  cfi->state = CFI_STATE_READ_ID;
+	  goto done;
+	}
+
+      /* Fall through.  */
+
+    default:
+      if (!cfi->cmdset->write (me, cfi, source, offset, value, nr_bytes))
+	HW_TRACE ((me, "unhandled command %#x at %#x", value, offset));
+      break;
+    }
+
+ done:
+  HW_TRACE ((me, "write 0x%08lx command {%#x,%#x,%#x,%#x}; state %s -> %s",
+	     (unsigned long) addr, ssource[0],
+	     nr_bytes > 1 ? ssource[1] : 0,
+	     nr_bytes > 2 ? ssource[2] : 0,
+	     nr_bytes > 3 ? ssource[3] : 0,
+	     state_names[old_state], state_names[cfi->state]));
+
+  return nr_bytes;
+}
+
+/* All reads to the flash address space come here.  Using the state machine,
+   we figure out what to return -- actual data stored in the flash, the CFI
+   query structure, some status info, or something else ?  Any requests that
+   we can't handle are passed to the command set-specific read function.  */
+static unsigned
+cfi_io_read_buffer (struct hw *me, void *dest, int space,
+		    address_word addr, unsigned nr_bytes)
+{
+  struct cfi *cfi = hw_data (me);
+  unsigned char *sdest = dest;
+  unsigned offset, shifted_offset;
+
+  offset = addr & (cfi->dev_size - 1);
+  shifted_offset = cfi_unshift_addr (cfi, offset);
+
+  /* XXX: Is this OK to enforce ?  */
+#if 0
+  if (cfi->state != CFI_STATE_READ && cfi->width != nr_bytes)
+    {
+      HW_TRACE ((me, "read 0x%08lx length %u does not match flash width %u",
+		 (unsigned long) addr, nr_bytes, cfi->width));
+      return nr_bytes;
+    }
+#endif
+
+  HW_TRACE ((me, "%s read 0x%08lx length %u",
+	     state_names[cfi->state], (unsigned long) addr, nr_bytes));
+
+  switch (cfi->state)
+    {
+    case CFI_STATE_READ:
+      memcpy (dest, cfi->data + offset, nr_bytes);
+      break;
+
+    case CFI_STATE_CFI_QUERY:
+      if (shifted_offset >= CFI_ADDR_CFI_QUERY_RESULT &&
+	  shifted_offset < CFI_ADDR_CFI_QUERY_RESULT + sizeof (cfi->query) +
+		     (cfi->query.num_erase_regions * 4))
+	{
+	  unsigned char *qry;
+
+	  shifted_offset -= CFI_ADDR_CFI_QUERY_RESULT;
+	  if (shifted_offset >= sizeof (cfi->query))
+	    {
+	      qry = cfi->erase_region_info;
+	      shifted_offset -= sizeof (cfi->query);
+	    }
+	  else
+	    qry = (void *) &cfi->query;
+
+	  sdest[0] = qry[shifted_offset];
+	  memset (sdest + 1, 0, nr_bytes - 1);
+
+	  break;
+	}
+
+    default:
+      if (!cfi->cmdset->read (me, cfi, dest, offset, shifted_offset, nr_bytes))
+	HW_TRACE ((me, "unhandled state %s", state_names[cfi->state]));
+      break;
+    }
+
+  return nr_bytes;
+}
+
+/* Clean up any state when this device is removed (e.g. when shutting down,
+   or when reloading via gdb).  */
+static void
+cfi_delete_callback (struct hw *me)
+{
+#ifdef HAVE_MMAP
+  struct cfi *cfi = hw_data (me);
+
+  if (cfi->mmap)
+    munmap (cfi->mmap, cfi->dev_size);
+#endif
+}
+
+/* Helper function to easily add CFI erase regions to the existing set.  */
+static void
+cfi_add_erase_region (struct hw *me, struct cfi *cfi,
+		      unsigned blocks, unsigned size)
+{
+  unsigned num_regions = cfi->query.num_erase_regions;
+  struct cfi_erase_region *region;
+  unsigned char *qry_region;
+
+  /* Store for our own usage.  */
+  region = &cfi->erase_regions[num_regions];
+  region->blocks = blocks;
+  region->size = size;
+  if (num_regions == 0)
+    region->start = 0;
+  else
+    region->start = region[-1].end;
+  region->end = region->start + (blocks * size);
+
+  /* Regions are 4 bytes long.  */
+  qry_region = cfi->erase_region_info + 4 * num_regions;
+
+  /* [0][1] = number erase blocks - 1 */
+  if (blocks > 0xffff + 1)
+    hw_abort (me, "erase blocks %u too big to fit into region info", blocks);
+  cfi_encode_16bit (&qry_region[0], blocks - 1);
+
+  /* [2][3] = block size / 256 bytes */
+  if (size > 0xffff * 256)
+    hw_abort (me, "erase size %u too big to fit into region info", size);
+  cfi_encode_16bit (&qry_region[2], size / 256);
+
+  /* Yet another region.  */
+  cfi->query.num_erase_regions = num_regions + 1;
+}
+
+/* Device tree options:
+     Required:
+       .../reg <addr> <len>
+       .../cmdset <primary; integer> [alt; integer]
+     Optional:
+       .../size <device size (must be pow of 2)>
+       .../width <8|16|32>
+       .../write_size <integer (must be pow of 2)>
+       .../erase_regions <number blocks> <block size> \
+                         [<number blocks> <block size> ...]
+       .../voltage <vcc min> <vcc max> <vpp min> <vpp max>
+       .../timeouts <typ unit write>  <typ buf write>  \
+                    <typ block erase> <typ chip erase> \
+                    <max unit write>  <max buf write>  \
+                    <max block erase> <max chip erase>
+       .../file <file> [ro|rw]
+     Defaults:
+       size: <len> from "reg"
+       width: 8
+       write_size: 0 (not supported)
+       erase_region: 1 (can only erase whole chip)
+       voltage: 0.0V (for all)
+       timeouts: typ: 1µs, not supported, 1ms, not supported
+                 max: 1µs, 1ms, 1ms, not supported
+
+  TODO: Verify user args are valid (e.g. voltage is 8 bits).  */
+static void
+attach_cfi_regs (struct hw *me, struct cfi *cfi)
+{
+  address_word attach_address;
+  int attach_space;
+  unsigned attach_size;
+  reg_property_spec reg;
+  bool fd_writable;
+  int i, ret, fd;
+  signed_cell ival;
+
+  if (hw_find_property (me, "reg") == NULL)
+    hw_abort (me, "Missing \"reg\" property");
+  if (hw_find_property (me, "cmdset") == NULL)
+    hw_abort (me, "Missing \"cmdset\" property");
+
+  if (!hw_find_reg_array_property (me, "reg", 0, &reg))
+    hw_abort (me, "\"reg\" property must contain three addr/size entries");
+
+  hw_unit_address_to_attach_address (hw_parent (me),
+				     &reg.address,
+				     &attach_space, &attach_address, me);
+  hw_unit_size_to_attach_size (hw_parent (me), &reg.size, &attach_size, me);
+
+  hw_attach_address (hw_parent (me),
+		     0, attach_space, attach_address, attach_size, me);
+
+  /* Extract the desired flash command set.  */
+  ret = hw_find_integer_array_property (me, "cmdset", 0, &ival);
+  if (ret != 1 && ret != 2)
+    hw_abort (me, "\"cmdset\" property takes 1 or 2 entries");
+  cfi_encode_16bit (cfi->query.p_id, ival);
+
+  for (i = 0; i < ARRAY_SIZE (cfi_cmdsets); ++i)
+    if (cfi_cmdsets[i]->id == ival)
+      cfi->cmdset = cfi_cmdsets[i];
+  if (cfi->cmdset == NULL)
+    hw_abort (me, "cmdset %u not supported", ival);
+
+  if (ret == 2)
+    {
+      hw_find_integer_array_property (me, "cmdset", 1, &ival);
+      cfi_encode_16bit (cfi->query.a_id, ival);
+    }
+
+  /* Extract the desired device size.  */
+  if (hw_find_property (me, "size"))
+    cfi->dev_size = hw_find_integer_property (me, "size");
+  else
+    cfi->dev_size = attach_size;
+  cfi->query.dev_size = log2 (cfi->dev_size);
+
+  /* Extract the desired flash width.  */
+  if (hw_find_property (me, "width"))
+    {
+      cfi->width = hw_find_integer_property (me, "width");
+      if (cfi->width != 8 && cfi->width != 16 && cfi->width != 32)
+	hw_abort (me, "\"width\" must be 8 or 16 or 32, not %u", cfi->width);
+    }
+  else
+    /* Default to 8 bit.  */
+    cfi->width = 8;
+  /* Turn 8/16/32 into 1/2/4.  */
+  cfi->width /= 8;
+
+  /* Extract optional write buffer size.  */
+  if (hw_find_property (me, "write_size"))
+    {
+      ival = hw_find_integer_property (me, "write_size");
+      cfi_encode_16bit (cfi->query.max_buf_write_len, log2 (ival));
+    }
+
+  /* Extract optional erase regions.  */
+  if (hw_find_property (me, "erase_regions"))
+    {
+      ret = hw_find_integer_array_property (me, "erase_regions", 0, &ival);
+      if (ret % 2)
+	hw_abort (me, "\"erase_regions\" must be specified in sets of 2");
+
+      cfi->erase_region_info = HW_NALLOC (me, unsigned char, ret / 2);
+      cfi->erase_regions = HW_NALLOC (me, struct cfi_erase_region, ret / 2);
+
+      for (i = 0; i < ret; i += 2)
+	{
+	  unsigned blocks, size;
+
+	  hw_find_integer_array_property (me, "erase_regions", i, &ival);
+	  blocks = ival;
+
+	  hw_find_integer_array_property (me, "erase_regions", i + 1, &ival);
+	  size = ival;
+
+	  cfi_add_erase_region (me, cfi, blocks, size);
+	}
+    }
+
+  /* Extract optional voltages.  */
+  if (hw_find_property (me, "voltage"))
+    {
+      unsigned num = ARRAY_SIZE (cfi->query.voltages);
+
+      ret = hw_find_integer_array_property (me, "voltage", 0, &ival);
+      if (ret > num)
+	hw_abort (me, "\"voltage\" may have only %u arguments", num);
+
+      for (i = 0; i < ret; ++i)
+	{
+	  hw_find_integer_array_property (me, "voltage", i, &ival);
+	  cfi->query.voltages[i] = ival;
+	}
+    }
+
+  /* Extract optional timeouts.  */
+  if (hw_find_property (me, "timeout"))
+    {
+      unsigned num = ARRAY_SIZE (cfi->query.timeouts);
+
+      ret = hw_find_integer_array_property (me, "timeout", 0, &ival);
+      if (ret > num)
+	hw_abort (me, "\"timeout\" may have only %u arguments", num);
+
+      for (i = 0; i < ret; ++i)
+	{
+	  hw_find_integer_array_property (me, "timeout", i, &ival);
+	  cfi->query.timeouts[i] = ival;
+	}
+    }
+
+  /* Extract optional file.  */
+  fd = -1;
+  fd_writable = false;
+  if (hw_find_property (me, "file"))
+    {
+      const char *file;
+
+      ret = hw_find_string_array_property (me, "file", 0, &file);
+      if (ret > 2)
+	hw_abort (me, "\"file\" may take only one argument");
+      if (ret == 2)
+	{
+	  const char *writable;
+
+	  hw_find_string_array_property (me, "file", 1, &writable);
+	  fd_writable = !strcmp (writable, "rw");
+	}
+
+      fd = open (file, fd_writable ? O_RDWR : O_RDONLY);
+      if (fd < 0)
+	hw_abort (me, "unable to read file `%s': %s", file, strerror (errno));
+    }
+
+  /* Figure out where our initial flash data is coming from.  */
+#ifdef HAVE_MMAP
+  if (fd != -1 && fd_writable)
+    {
+      posix_fallocate (fd, 0, cfi->dev_size);
+
+      cfi->mmap = mmap (NULL, cfi->dev_size,
+			PROT_READ | (fd_writable ? PROT_WRITE : 0),
+			MAP_SHARED, fd, 0);
+
+      if (cfi->mmap == MAP_FAILED)
+	cfi->mmap = NULL;
+      else
+	cfi->data = cfi->mmap;
+    }
+#endif
+  if (!cfi->data)
+    {
+      ssize_t read_len;
+
+      cfi->data = HW_NALLOC (me, unsigned char, cfi->dev_size);
+      if (fd != -1)
+	read_len = read (fd, cfi->data, cfi->dev_size);
+      else
+	read_len = 0;
+      memset (cfi->data, 0xff, cfi->dev_size - read_len);
+    }
+
+  close (fd);
+}
+
+/* Once we've been declared in the device tree, this is the main entry point.
+   So allocate state, attach memory addresses, and all that fun stuff.  */
+static void
+cfi_finish (struct hw *me)
+{
+  struct cfi *cfi;
+
+  cfi = HW_ZALLOC (me, struct cfi);
+
+  set_hw_data (me, cfi);
+  set_hw_io_read_buffer (me, cfi_io_read_buffer);
+  set_hw_io_write_buffer (me, cfi_io_write_buffer);
+  set_hw_delete (me, cfi_delete_callback);
+
+  attach_cfi_regs (me, cfi);
+
+  /* Initialize the CFI.  */
+  cfi->state = CFI_STATE_READ;
+  memcpy (cfi->query.qry, "QRY", 3);
+  cfi->cmdset->setup (me, cfi);
+}
+
+/* Every device is required to declare this.  */
+const struct hw_descriptor dv_cfi_descriptor[] =
+{
+  {"cfi", cfi_finish,},
+  {NULL, NULL},
+};
diff --git a/sim/common/dv-cfi.h b/sim/common/dv-cfi.h
new file mode 100644
index 0000000..bd2db2d
--- /dev/null
+++ b/sim/common/dv-cfi.h
@@ -0,0 +1,60 @@
+/* Common Flash Memory Interface (CFI) model.
+
+   Copyright (C) 2010 Free Software Foundation, Inc.
+   Contributed by Analog Devices, Inc.
+
+   This file is part of simulators.
+
+   This program is free software; you can redistribute it and/or modify
+   it under the terms of the GNU General Public License as published by
+   the Free Software Foundation; either version 3 of the License, or
+   (at your option) any later version.
+
+   This program is distributed in the hope that it will be useful,
+   but WITHOUT ANY WARRANTY; without even the implied warranty of
+   MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+   GNU General Public License for more details.
+
+   You should have received a copy of the GNU General Public License
+   along with this program.  If not, see <http://www.gnu.org/licenses/>.  */
+
+#ifndef DV_CFI_H
+#define DV_CFI_H
+
+/* CFI standard.  */
+#define CFI_CMD_CFI_QUERY		0x98
+#define CFI_ADDR_CFI_QUERY_START	0x55
+#define CFI_ADDR_CFI_QUERY_RESULT	0x10
+
+#define CFI_CMD_READ			0xFF
+#define CFI_CMD_RESET			0xF0
+#define CFI_CMD_READ_ID			0x90
+
+/* Intel specific.  */
+#define CFI_CMDSET_INTEL		0x0001
+#define INTEL_CMD_STATUS_CLEAR		0x50
+#define INTEL_CMD_STATUS_READ		0x70
+#define INTEL_CMD_WRITE			0x40
+#define INTEL_CMD_WRITE_ALT		0x10
+#define INTEL_CMD_WRITE_BUFFER		0xE8
+#define INTEL_CMD_WRITE_BUFFER_CONFIRM	0xD0
+#define INTEL_CMD_LOCK_SETUP		0x60
+#define INTEL_CMD_LOCK_BLOCK		0x01
+#define INTEL_CMD_UNLOCK_BLOCK		0xD0
+#define INTEL_CMD_LOCK_DOWN_BLOCK	0x2F
+#define INTEL_CMD_ERASE_BLOCK		0x20
+#define INTEL_CMD_ERASE_CONFIRM		0xD0
+
+/* Intel Status Register bits.  */
+#define INTEL_SR_BWS		(1 << 0)	/* BEFP Write.  */
+#define INTEL_SR_BLS		(1 << 1)	/* Block Locked.  */
+#define INTEL_SR_PSS		(1 << 2)	/* Program Suspend.  */
+#define INTEL_SR_VPPS		(1 << 3)	/* Vpp.  */
+#define INTEL_SR_PS		(1 << 4)	/* Program.  */
+#define INTEL_SR_ES		(1 << 5)	/* Erase.  */
+#define INTEL_SR_ESS		(1 << 6)	/* Erase Suspend.  */
+#define INTEL_SR_DWS		(1 << 7)	/* Device Write.  */
+
+#define INTEL_ID_MANU		0x89
+
+#endif
-- 
1.7.4.1

Re: =?UTF-8?q?=5BPATCH=20v3=5D=20sim=3A=20cfi=3A=20new=20flash=20device=20simulation?=

[Frank Ch. Eigler]

vapier wrote:

> This simulates a CFI flash.  [...]

Nice work, good looking code.  Only some tiny nits:

> +static unsigned
> +cfi_unshift_addr (struct cfi *cfi, unsigned addr)
> +{
> +  switch (cfi->width)
> +    {
> +    case 4: addr >>= 1;
> +    case 2: addr >>= 1;
> +    }

A note about the deliberate case fallthrough might be nice.


> +/* Clean up any state when this device is removed (e.g. when shutting down,
> +   or when reloading via gdb).  */
> +static void
> +cfi_delete_callback (struct hw *me)
> +{
> +#ifdef HAVE_MMAP
> +  struct cfi *cfi = hw_data (me);
> +
> +  if (cfi->mmap)
> +    munmap (cfi->mmap, cfi->dev_size);
> +#endif
> +}

Woudln't you want to write(2) out the contents of the flash backing
store file, if !HAVE_MMAP?


> +static void
> +attach_cfi_regs (struct hw *me, struct cfi *cfi)
> +[...]
> +      cfi->data = HW_NALLOC (me, unsigned char, cfi->dev_size);
> +      if (fd != -1)
> +	read_len = read (fd, cfi->data, cfi->dev_size);

It's more typical to loop in read(2), in case of an EINTR or somesuch
temporary-failure return code.  Or use fread(3)?


- FChE

Re: [PATCH v3] sim: cfi: new flash device simulation

[Joel Brobecker]

> gdb/:
> 2011-03-24  Mike Frysinger  <vapier@gentoo.org>
> 
> 	* NEWS: Mention new cfi device simulation.
> 
> sim/common/:
> 2011-03-24  Mike Frysinger  <vapier@gentoo.org>
> 
> 	* aclocal.m4 (SIM_AC_OPTION_HARDWARE): Add cfi to default list.
> 	* Make-common.in (dv-cfi.o): New rule.
> 	* dv-cfi.c, dv-cfi.h: New files.

It's great to see the code with the comments, thanks! If you are going
to produce a 4th version based on Frank's comments, it would be nice
to reformat the comments a little to limit the length to 70 characters.
That's the soft limit we decided on recently. We allow ourselves to go
beyond that limit if it helping making thing less ugly, but otherwise,
we try to stay within that limit.  If you're not going to produce
a new version, then no worries about that.


-- 
Joel

[PATCH v4] sim: cfi: new flash device simulation

[Mike Frysinger]

This simulates a CFI flash.  Its pretty configurable via the device
tree.  For now, only basic read/write/erase operations are supported
for the Intel command set, but it's easy enough to extend support.
It's certainly enough to trick Das U-Boot into using it for probing,
reading, writing, and erasing.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

gdb/:
2011-03-24  Mike Frysinger  <vapier@gentoo.org>

	* NEWS: Mention new cfi device simulation.

sim/common/:
2011-03-24  Mike Frysinger  <vapier@gentoo.org>

	* aclocal.m4 (SIM_AC_OPTION_HARDWARE): Add cfi to default list.
	* Make-common.in (dv-cfi.o): New rule.
	* dv-cfi.c, dv-cfi.h: New files.
---
v4
	- wrap comments a bit more to ~70 cols
	- use fread() instead of read() to avoid possible EINTR edge cases
	- add a warning when rw is requested but mmap() is not available

 gdb/NEWS                  |    2 +
 sim/common/Make-common.in |    3 +
 sim/common/aclocal.m4     |    2 +-
 sim/common/dv-cfi.c       |  799 +++++++++++++++++++++++++++++++++++++++++++++
 sim/common/dv-cfi.h       |   60 ++++
 5 files changed, 865 insertions(+), 1 deletions(-)
 create mode 100644 sim/common/dv-cfi.c
 create mode 100644 sim/common/dv-cfi.h

diff --git a/gdb/NEWS b/gdb/NEWS
index 2288497..a09395c 100644
--- a/gdb/NEWS
+++ b/gdb/NEWS
@@ -182,6 +182,8 @@ Analog Devices, Inc. Blackfin Processor	bfin-*
 
   ** The --map-info flag lists all known core mappings.
 
+  ** CFI flashes may be simulated via the "cfi" device.
+
 *** Changes in GDB 7.2
 
 * Shared library support for remote targets by default
diff --git a/sim/common/Make-common.in b/sim/common/Make-common.in
index 2f0c807..42e3192 100644
--- a/sim/common/Make-common.in
+++ b/sim/common/Make-common.in
@@ -579,6 +579,9 @@ hw-tree.o: $(srccom)/hw-tree.c $(hw_main_headers) $(hw-tree_h)
 
 # Devices.
 
+dv-cfi.o: $(srccom)/dv-cfi.c $(hw_main_headers) $(sim_main_headers)
+	$(CC) -c $(srccom)/dv-cfi.c $(ALL_CFLAGS)
+
 dv-core.o: $(srccom)/dv-core.c $(hw_main_headers) $(sim_main_headers)
 	$(CC) -c $(srccom)/dv-core.c $(ALL_CFLAGS)
 
diff --git a/sim/common/aclocal.m4 b/sim/common/aclocal.m4
index bda20ce..cec0155 100644
--- a/sim/common/aclocal.m4
+++ b/sim/common/aclocal.m4
@@ -573,7 +573,7 @@ fi
 if test "[$2]"; then
   hardware="[$2]"
 else
-  hardware="core pal glue"
+  hardware="cfi core pal glue"
 fi
 hardware="$hardware [$3]"
 sim_hw_cflags="-DWITH_HW=1"
diff --git a/sim/common/dv-cfi.c b/sim/common/dv-cfi.c
new file mode 100644
index 0000000..52dcf45
--- /dev/null
+++ b/sim/common/dv-cfi.c
@@ -0,0 +1,799 @@
+/* Common Flash Memory Interface (CFI) model.
+   http://www.spansion.com/Support/AppNotes/CFI_Spec_AN_03.pdf
+   http://www.spansion.com/Support/AppNotes/cfi_100_20011201.pdf
+
+   Copyright (C) 2010-2011 Free Software Foundation, Inc.
+   Contributed by Analog Devices, Inc.
+
+   This file is part of simulators.
+
+   This program is free software; you can redistribute it and/or modify
+   it under the terms of the GNU General Public License as published by
+   the Free Software Foundation; either version 3 of the License, or
+   (at your option) any later version.
+
+   This program is distributed in the hope that it will be useful,
+   but WITHOUT ANY WARRANTY; without even the implied warranty of
+   MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+   GNU General Public License for more details.
+
+   You should have received a copy of the GNU General Public License
+   along with this program.  If not, see <http://www.gnu.org/licenses/>.  */
+
+/* TODO: support vendor query tables.  */
+
+#include "cconfig.h"
+
+#include <math.h>
+#include <errno.h>
+#include <fcntl.h>
+#include <unistd.h>
+#ifdef HAVE_SYS_MMAN_H
+#include <sys/mman.h>
+#endif
+
+#include "sim-main.h"
+#include "devices.h"
+#include "dv-cfi.h"
+
+/* Flashes are simple state machines, so here we cover all the
+   different states a device might be in at any particular time.  */
+enum cfi_state
+{
+  CFI_STATE_READ,
+  CFI_STATE_READ_ID,
+  CFI_STATE_CFI_QUERY,
+  CFI_STATE_PROTECT,
+  CFI_STATE_STATUS,
+  CFI_STATE_ERASE,
+  CFI_STATE_WRITE,
+  CFI_STATE_WRITE_BUFFER,
+  CFI_STATE_WRITE_BUFFER_CONFIRM,
+};
+
+/* This is the structure that all CFI conforming devices must provided
+   when asked for it.  This allows a single driver to dynamically support
+   different flash geometries without having to hardcode specs.
+
+   If you want to start mucking about here, you should just grab the
+   CFI spec and review that (see top of this file for URIs).  */
+struct cfi_query
+{
+  /* This is always 'Q' 'R' 'Y'.  */
+  unsigned char qry[3];
+  /* Primary vendor ID.  */
+  unsigned char p_id[2];
+  /* Primary query table address.  */
+  unsigned char p_adr[2];
+  /* Alternate vendor ID.  */
+  unsigned char a_id[2];
+  /* Alternate query table address.  */
+  unsigned char a_adr[2];
+  union
+  {
+    /* Voltage levels.  */
+    unsigned char voltages[4];
+    struct
+    {
+      /* Normal min voltage level.  */
+      unsigned char vcc_min;
+      /* Normal max voltage level.  */
+      unsigned char vcc_max;
+      /* Programming min volage level.  */
+      unsigned char vpp_min;
+      /* Programming max volage level.  */
+      unsigned char vpp_max;
+    };
+  };
+  union
+  {
+    /* Operational timeouts.  */
+    unsigned char timeouts[8];
+    struct
+    {
+      /* Typical timeout for writing a single "unit".  */
+      unsigned char timeout_typ_unit_write;
+      /* Typical timeout for writing a single "buffer".  */
+      unsigned char timeout_typ_buf_write;
+      /* Typical timeout for erasing a block.  */
+      unsigned char timeout_typ_block_erase;
+      /* Typical timeout for erasing the chip.  */
+      unsigned char timeout_typ_chip_erase;
+      /* Max timeout for writing a single "unit".  */
+      unsigned char timeout_max_unit_write;
+      /* Max timeout for writing a single "buffer".  */
+      unsigned char timeout_max_buf_write;
+      /* Max timeout for erasing a block.  */
+      unsigned char timeout_max_block_erase;
+      /* Max timeout for erasing the chip.  */
+      unsigned char timeout_max_chip_erase;
+    };
+  };
+  /* Flash size is 2^dev_size bytes.  */
+  unsigned char dev_size;
+  /* Flash device interface description.  */
+  unsigned char iface_desc[2];
+  /* Max length of a single buffer write is 2^max_buf_write_len bytes.  */
+  unsigned char max_buf_write_len[2];
+  /* Number of erase regions.  */
+  unsigned char num_erase_regions;
+  /* The erase regions would now be an array after this point, but since
+     it is dynamic, we'll provide that from "struct cfi" when requested.  */
+  /*unsigned char erase_region_info;*/
+};
+
+/* Flashes may have regions with different erase sizes.  There is one
+   structure per erase region.  */
+struct cfi_erase_region
+{
+  unsigned blocks;
+  unsigned size;
+  unsigned start;
+  unsigned end;
+};
+
+struct cfi;
+
+/* Flashes are accessed via commands -- you write a certain number to
+   a special address to change the flash state and access info other
+   than the data.  Diff companies have implemented their own command
+   set.  This structure abstracts the different command sets so that
+   we can support multiple ones with just a single sim driver.  */
+struct cfi_cmdset
+{
+  unsigned id;
+  void (*setup) (struct hw *me, struct cfi *cfi);
+  bool (*write) (struct hw *me, struct cfi *cfi, const void *source,
+		 unsigned offset, unsigned value, unsigned nr_bytes);
+  bool (*read) (struct hw *me, struct cfi *cfi, void *dest,
+		unsigned offset, unsigned shifted_offset, unsigned nr_bytes);
+};
+
+/* The per-flash state.  Much of this comes from the device tree which
+   people declare themselves.  See top of attach_cfi_regs() for more
+   info.  */
+struct cfi
+{
+  unsigned width, dev_size, status;
+  enum cfi_state state;
+  unsigned char *data, *mmap;
+
+  struct cfi_query query;
+  const struct cfi_cmdset *cmdset;
+
+  unsigned char *erase_region_info;
+  struct cfi_erase_region *erase_regions;
+};
+
+/* Helpful strings which are used with HW_TRACE.  */
+static const char * const state_names[] =
+{
+  "READ", "READ_ID", "CFI_QUERY", "PROTECT", "STATUS", "ERASE", "WRITE",
+  "WRITE_BUFFER", "WRITE_BUFFER_CONFIRM",
+};
+\f
+/* Erase the block specified by the offset into the given CFI flash.  */
+static void
+cfi_erase_block (struct hw *me, struct cfi *cfi, unsigned offset)
+{
+  unsigned i;
+  struct cfi_erase_region *region;
+
+  /* If no erase regions, then we can only do whole chip erase.  */
+  /* XXX: Is this within spec ?  Or must there always be at least one ?  */
+  if (!cfi->query.num_erase_regions)
+    memset (cfi->data, 0xff, cfi->dev_size);
+
+  for (i = 0; i < cfi->query.num_erase_regions; ++i)
+    {
+      region = &cfi->erase_regions[i];
+
+      if (offset >= region->end)
+	continue;
+
+      /* XXX: Does spec require the erase addr to be erase block aligned ?
+	      Maybe this is check is overly cautious ...  */
+      offset &= ~(region->size - 1);
+      memset (cfi->data + offset, 0xff, region->size);
+      break;
+    }
+}
+
+/* Depending on the bus width, addresses might be bit shifted.  This
+   helps us normalize everything without cluttering up the rest of
+   the code.  */
+static unsigned
+cfi_unshift_addr (struct cfi *cfi, unsigned addr)
+{
+  switch (cfi->width)
+    {
+    case 4: addr >>= 1; /* fallthrough.  */
+    case 2: addr >>= 1;
+    }
+  return addr;
+}
+
+/* CFI requires all values to be little endian in its structure, so
+   this helper writes a 16bit value into a little endian byte buffer.  */
+static void
+cfi_encode_16bit (unsigned char *data, unsigned num)
+{
+  data[0] = num;
+  data[1] = num >> 8;
+}
+\f
+/* The functions required to implement the Intel command set.  */
+
+static bool
+cmdset_intel_write (struct hw *me, struct cfi *cfi, const void *source,
+		    unsigned offset, unsigned value, unsigned nr_bytes)
+{
+  switch (cfi->state)
+    {
+    case CFI_STATE_READ:
+    case CFI_STATE_READ_ID:
+      switch (value)
+	{
+	case INTEL_CMD_ERASE_BLOCK:
+	  cfi->state = CFI_STATE_ERASE;
+	  break;
+	case INTEL_CMD_WRITE:
+	case INTEL_CMD_WRITE_ALT:
+	  cfi->state = CFI_STATE_WRITE;
+	  break;
+	case INTEL_CMD_STATUS_CLEAR:
+	  cfi->status = INTEL_SR_DWS;
+	  break;
+	case INTEL_CMD_LOCK_SETUP:
+	  cfi->state = CFI_STATE_PROTECT;
+	  break;
+	default:
+	  return false;
+	}
+      break;
+
+    case CFI_STATE_ERASE:
+      if (value == INTEL_CMD_ERASE_CONFIRM)
+	{
+	  cfi_erase_block (me, cfi, offset);
+	  cfi->status &= ~(INTEL_SR_PS | INTEL_SR_ES);
+	}
+      else
+	cfi->status |= INTEL_SR_PS | INTEL_SR_ES;
+      cfi->state = CFI_STATE_STATUS;
+      break;
+
+    case CFI_STATE_PROTECT:
+      switch (value)
+	{
+	case INTEL_CMD_LOCK_BLOCK:
+	case INTEL_CMD_UNLOCK_BLOCK:
+	case INTEL_CMD_LOCK_DOWN_BLOCK:
+	  /* XXX: Handle the command.  */
+	  break;
+	default:
+	  /* Kick out.  */
+	  cfi->status |= INTEL_SR_PS | INTEL_SR_ES;
+	  break;
+	}
+      cfi->state = CFI_STATE_STATUS;
+      break;
+
+    default:
+      return false;
+    }
+
+  return true;
+}
+
+static bool
+cmdset_intel_read (struct hw *me, struct cfi *cfi, void *dest,
+		   unsigned offset, unsigned shifted_offset, unsigned nr_bytes)
+{
+  unsigned char *sdest = dest;
+
+  switch (cfi->state)
+    {
+    case CFI_STATE_STATUS:
+    case CFI_STATE_ERASE:
+      *sdest = cfi->status;
+      break;
+
+    case CFI_STATE_READ_ID:
+      switch (shifted_offset & 0x1ff)
+	{
+	case 0x00:	/* Manufacturer Code.  */
+	  cfi_encode_16bit (dest, INTEL_ID_MANU);
+	  break;
+	case 0x01:	/* Device ID Code.  */
+	  /* XXX: Push to device tree ?  */
+	  cfi_encode_16bit (dest, 0xad);
+	  break;
+	case 0x02:	/* Block lock state.  */
+	  /* XXX: This is per-block ...  */
+	  *sdest = 0x00;
+	  break;
+	case 0x05:	/* Read Configuration Register.  */
+	  cfi_encode_16bit (dest, (1 << 15));
+	  break;
+	default:
+	  return false;
+	}
+      break;
+
+    default:
+      return false;
+    }
+
+  return true;
+}
+
+static void
+cmdset_intel_setup (struct hw *me, struct cfi *cfi)
+{
+  cfi->status = INTEL_SR_DWS;
+}
+
+static const struct cfi_cmdset cfi_cmdset_intel =
+{
+  CFI_CMDSET_INTEL, cmdset_intel_setup, cmdset_intel_write, cmdset_intel_read,
+};
+\f
+/* All of the supported command sets get listed here.  We then walk this
+   array to see if the user requested command set is implemented.  */
+static const struct cfi_cmdset * const cfi_cmdsets[] =
+{
+  &cfi_cmdset_intel,
+};
+\f
+/* All writes to the flash address space come here.  Using the state
+   machine, we figure out what to do with this specific write.  All
+   common code sits here and if there is a request we can't process,
+   we hand it off to the command set-specific write function.  */
+static unsigned
+cfi_io_write_buffer (struct hw *me, const void *source, int space,
+		     address_word addr, unsigned nr_bytes)
+{
+  struct cfi *cfi = hw_data (me);
+  const unsigned char *ssource = source;
+  enum cfi_state old_state;
+  unsigned offset, shifted_offset, value;
+
+  offset = addr & (cfi->dev_size - 1);
+  shifted_offset = cfi_unshift_addr (cfi, offset);
+
+  if (cfi->width != nr_bytes)
+    {
+      HW_TRACE ((me, "write 0x%08lx length %u does not match flash width %u",
+		 (unsigned long) addr, nr_bytes, cfi->width));
+      return nr_bytes;
+    }
+
+  if (cfi->state == CFI_STATE_WRITE)
+    {
+      /* NOR flash can only go from 1 to 0.  */
+      unsigned i;
+
+      HW_TRACE ((me, "program %#x length %u", offset, nr_bytes));
+
+      for (i = 0; i < nr_bytes; ++i)
+	cfi->data[offset + i] &= ssource[i];
+
+      cfi->state = CFI_STATE_STATUS;
+
+      return nr_bytes;
+    }
+
+  value = ssource[0];
+
+  old_state = cfi->state;
+
+  if (value == CFI_CMD_READ || value == CFI_CMD_RESET)
+    {
+      cfi->state = CFI_STATE_READ;
+      goto done;
+    }
+
+  switch (cfi->state)
+    {
+    case CFI_STATE_READ:
+    case CFI_STATE_READ_ID:
+      if (value == CFI_CMD_CFI_QUERY)
+	{
+	  if (shifted_offset == CFI_ADDR_CFI_QUERY_START)
+	    cfi->state = CFI_STATE_CFI_QUERY;
+	  goto done;
+	}
+
+      if (value == CFI_CMD_READ_ID)
+	{
+	  cfi->state = CFI_STATE_READ_ID;
+	  goto done;
+	}
+
+      /* Fall through.  */
+
+    default:
+      if (!cfi->cmdset->write (me, cfi, source, offset, value, nr_bytes))
+	HW_TRACE ((me, "unhandled command %#x at %#x", value, offset));
+      break;
+    }
+
+ done:
+  HW_TRACE ((me, "write 0x%08lx command {%#x,%#x,%#x,%#x}; state %s -> %s",
+	     (unsigned long) addr, ssource[0],
+	     nr_bytes > 1 ? ssource[1] : 0,
+	     nr_bytes > 2 ? ssource[2] : 0,
+	     nr_bytes > 3 ? ssource[3] : 0,
+	     state_names[old_state], state_names[cfi->state]));
+
+  return nr_bytes;
+}
+
+/* All reads to the flash address space come here.  Using the state
+   machine, we figure out what to return -- actual data stored in the
+   flash, the CFI query structure, some status info, or something else ?
+   Any requests that we can't handle are passed to the command set-
+   specific read function.  */
+static unsigned
+cfi_io_read_buffer (struct hw *me, void *dest, int space,
+		    address_word addr, unsigned nr_bytes)
+{
+  struct cfi *cfi = hw_data (me);
+  unsigned char *sdest = dest;
+  unsigned offset, shifted_offset;
+
+  offset = addr & (cfi->dev_size - 1);
+  shifted_offset = cfi_unshift_addr (cfi, offset);
+
+  /* XXX: Is this OK to enforce ?  */
+#if 0
+  if (cfi->state != CFI_STATE_READ && cfi->width != nr_bytes)
+    {
+      HW_TRACE ((me, "read 0x%08lx length %u does not match flash width %u",
+		 (unsigned long) addr, nr_bytes, cfi->width));
+      return nr_bytes;
+    }
+#endif
+
+  HW_TRACE ((me, "%s read 0x%08lx length %u",
+	     state_names[cfi->state], (unsigned long) addr, nr_bytes));
+
+  switch (cfi->state)
+    {
+    case CFI_STATE_READ:
+      memcpy (dest, cfi->data + offset, nr_bytes);
+      break;
+
+    case CFI_STATE_CFI_QUERY:
+      if (shifted_offset >= CFI_ADDR_CFI_QUERY_RESULT &&
+	  shifted_offset < CFI_ADDR_CFI_QUERY_RESULT + sizeof (cfi->query) +
+		     (cfi->query.num_erase_regions * 4))
+	{
+	  unsigned char *qry;
+
+	  shifted_offset -= CFI_ADDR_CFI_QUERY_RESULT;
+	  if (shifted_offset >= sizeof (cfi->query))
+	    {
+	      qry = cfi->erase_region_info;
+	      shifted_offset -= sizeof (cfi->query);
+	    }
+	  else
+	    qry = (void *) &cfi->query;
+
+	  sdest[0] = qry[shifted_offset];
+	  memset (sdest + 1, 0, nr_bytes - 1);
+
+	  break;
+	}
+
+    default:
+      if (!cfi->cmdset->read (me, cfi, dest, offset, shifted_offset, nr_bytes))
+	HW_TRACE ((me, "unhandled state %s", state_names[cfi->state]));
+      break;
+    }
+
+  return nr_bytes;
+}
+
+/* Clean up any state when this device is removed (e.g. when shutting
+   down, or when reloading via gdb).  */
+static void
+cfi_delete_callback (struct hw *me)
+{
+#ifdef HAVE_MMAP
+  struct cfi *cfi = hw_data (me);
+
+  if (cfi->mmap)
+    munmap (cfi->mmap, cfi->dev_size);
+#endif
+}
+
+/* Helper function to easily add CFI erase regions to the existing set.  */
+static void
+cfi_add_erase_region (struct hw *me, struct cfi *cfi,
+		      unsigned blocks, unsigned size)
+{
+  unsigned num_regions = cfi->query.num_erase_regions;
+  struct cfi_erase_region *region;
+  unsigned char *qry_region;
+
+  /* Store for our own usage.  */
+  region = &cfi->erase_regions[num_regions];
+  region->blocks = blocks;
+  region->size = size;
+  if (num_regions == 0)
+    region->start = 0;
+  else
+    region->start = region[-1].end;
+  region->end = region->start + (blocks * size);
+
+  /* Regions are 4 bytes long.  */
+  qry_region = cfi->erase_region_info + 4 * num_regions;
+
+  /* [0][1] = number erase blocks - 1 */
+  if (blocks > 0xffff + 1)
+    hw_abort (me, "erase blocks %u too big to fit into region info", blocks);
+  cfi_encode_16bit (&qry_region[0], blocks - 1);
+
+  /* [2][3] = block size / 256 bytes */
+  if (size > 0xffff * 256)
+    hw_abort (me, "erase size %u too big to fit into region info", size);
+  cfi_encode_16bit (&qry_region[2], size / 256);
+
+  /* Yet another region.  */
+  cfi->query.num_erase_regions = num_regions + 1;
+}
+
+/* Device tree options:
+     Required:
+       .../reg <addr> <len>
+       .../cmdset <primary; integer> [alt; integer]
+     Optional:
+       .../size <device size (must be pow of 2)>
+       .../width <8|16|32>
+       .../write_size <integer (must be pow of 2)>
+       .../erase_regions <number blocks> <block size> \
+                         [<number blocks> <block size> ...]
+       .../voltage <vcc min> <vcc max> <vpp min> <vpp max>
+       .../timeouts <typ unit write>  <typ buf write>  \
+                    <typ block erase> <typ chip erase> \
+                    <max unit write>  <max buf write>  \
+                    <max block erase> <max chip erase>
+       .../file <file> [ro|rw]
+     Defaults:
+       size: <len> from "reg"
+       width: 8
+       write_size: 0 (not supported)
+       erase_region: 1 (can only erase whole chip)
+       voltage: 0.0V (for all)
+       timeouts: typ: 1µs, not supported, 1ms, not supported
+                 max: 1µs, 1ms, 1ms, not supported
+
+  TODO: Verify user args are valid (e.g. voltage is 8 bits).  */
+static void
+attach_cfi_regs (struct hw *me, struct cfi *cfi)
+{
+  address_word attach_address;
+  int attach_space;
+  unsigned attach_size;
+  reg_property_spec reg;
+  bool fd_writable;
+  int i, ret, fd;
+  signed_cell ival;
+
+  if (hw_find_property (me, "reg") == NULL)
+    hw_abort (me, "Missing \"reg\" property");
+  if (hw_find_property (me, "cmdset") == NULL)
+    hw_abort (me, "Missing \"cmdset\" property");
+
+  if (!hw_find_reg_array_property (me, "reg", 0, &reg))
+    hw_abort (me, "\"reg\" property must contain three addr/size entries");
+
+  hw_unit_address_to_attach_address (hw_parent (me),
+				     &reg.address,
+				     &attach_space, &attach_address, me);
+  hw_unit_size_to_attach_size (hw_parent (me), &reg.size, &attach_size, me);
+
+  hw_attach_address (hw_parent (me),
+		     0, attach_space, attach_address, attach_size, me);
+
+  /* Extract the desired flash command set.  */
+  ret = hw_find_integer_array_property (me, "cmdset", 0, &ival);
+  if (ret != 1 && ret != 2)
+    hw_abort (me, "\"cmdset\" property takes 1 or 2 entries");
+  cfi_encode_16bit (cfi->query.p_id, ival);
+
+  for (i = 0; i < ARRAY_SIZE (cfi_cmdsets); ++i)
+    if (cfi_cmdsets[i]->id == ival)
+      cfi->cmdset = cfi_cmdsets[i];
+  if (cfi->cmdset == NULL)
+    hw_abort (me, "cmdset %u not supported", ival);
+
+  if (ret == 2)
+    {
+      hw_find_integer_array_property (me, "cmdset", 1, &ival);
+      cfi_encode_16bit (cfi->query.a_id, ival);
+    }
+
+  /* Extract the desired device size.  */
+  if (hw_find_property (me, "size"))
+    cfi->dev_size = hw_find_integer_property (me, "size");
+  else
+    cfi->dev_size = attach_size;
+  cfi->query.dev_size = log2 (cfi->dev_size);
+
+  /* Extract the desired flash width.  */
+  if (hw_find_property (me, "width"))
+    {
+      cfi->width = hw_find_integer_property (me, "width");
+      if (cfi->width != 8 && cfi->width != 16 && cfi->width != 32)
+	hw_abort (me, "\"width\" must be 8 or 16 or 32, not %u", cfi->width);
+    }
+  else
+    /* Default to 8 bit.  */
+    cfi->width = 8;
+  /* Turn 8/16/32 into 1/2/4.  */
+  cfi->width /= 8;
+
+  /* Extract optional write buffer size.  */
+  if (hw_find_property (me, "write_size"))
+    {
+      ival = hw_find_integer_property (me, "write_size");
+      cfi_encode_16bit (cfi->query.max_buf_write_len, log2 (ival));
+    }
+
+  /* Extract optional erase regions.  */
+  if (hw_find_property (me, "erase_regions"))
+    {
+      ret = hw_find_integer_array_property (me, "erase_regions", 0, &ival);
+      if (ret % 2)
+	hw_abort (me, "\"erase_regions\" must be specified in sets of 2");
+
+      cfi->erase_region_info = HW_NALLOC (me, unsigned char, ret / 2);
+      cfi->erase_regions = HW_NALLOC (me, struct cfi_erase_region, ret / 2);
+
+      for (i = 0; i < ret; i += 2)
+	{
+	  unsigned blocks, size;
+
+	  hw_find_integer_array_property (me, "erase_regions", i, &ival);
+	  blocks = ival;
+
+	  hw_find_integer_array_property (me, "erase_regions", i + 1, &ival);
+	  size = ival;
+
+	  cfi_add_erase_region (me, cfi, blocks, size);
+	}
+    }
+
+  /* Extract optional voltages.  */
+  if (hw_find_property (me, "voltage"))
+    {
+      unsigned num = ARRAY_SIZE (cfi->query.voltages);
+
+      ret = hw_find_integer_array_property (me, "voltage", 0, &ival);
+      if (ret > num)
+	hw_abort (me, "\"voltage\" may have only %u arguments", num);
+
+      for (i = 0; i < ret; ++i)
+	{
+	  hw_find_integer_array_property (me, "voltage", i, &ival);
+	  cfi->query.voltages[i] = ival;
+	}
+    }
+
+  /* Extract optional timeouts.  */
+  if (hw_find_property (me, "timeout"))
+    {
+      unsigned num = ARRAY_SIZE (cfi->query.timeouts);
+
+      ret = hw_find_integer_array_property (me, "timeout", 0, &ival);
+      if (ret > num)
+	hw_abort (me, "\"timeout\" may have only %u arguments", num);
+
+      for (i = 0; i < ret; ++i)
+	{
+	  hw_find_integer_array_property (me, "timeout", i, &ival);
+	  cfi->query.timeouts[i] = ival;
+	}
+    }
+
+  /* Extract optional file.  */
+  fd = -1;
+  fd_writable = false;
+  if (hw_find_property (me, "file"))
+    {
+      const char *file;
+
+      ret = hw_find_string_array_property (me, "file", 0, &file);
+      if (ret > 2)
+	hw_abort (me, "\"file\" may take only one argument");
+      if (ret == 2)
+	{
+	  const char *writable;
+
+	  hw_find_string_array_property (me, "file", 1, &writable);
+	  fd_writable = !strcmp (writable, "rw");
+	}
+
+      fd = open (file, fd_writable ? O_RDWR : O_RDONLY);
+      if (fd < 0)
+	hw_abort (me, "unable to read file `%s': %s", file, strerror (errno));
+    }
+
+  /* Figure out where our initial flash data is coming from.  */
+  if (fd != -1 && fd_writable)
+    {
+#ifdef HAVE_MMAP
+      posix_fallocate (fd, 0, cfi->dev_size);
+
+      cfi->mmap = mmap (NULL, cfi->dev_size,
+			PROT_READ | (fd_writable ? PROT_WRITE : 0),
+			MAP_SHARED, fd, 0);
+
+      if (cfi->mmap == MAP_FAILED)
+	cfi->mmap = NULL;
+      else
+	cfi->data = cfi->mmap;
+#else
+      sim_io_eprintf (hw_system (me),
+		      "cfi: sorry, file write support requires mmap()\n");
+#endif
+    }
+  if (!cfi->data)
+    {
+      size_t read_len;
+
+      cfi->data = HW_NALLOC (me, unsigned char, cfi->dev_size);
+
+      if (fd != -1)
+	{
+	  /* Use stdio to avoid EINTR issues with read().  */
+	  FILE *fp = fdopen (fd, "r");
+
+	  if (fp)
+	    read_len = fread (cfi->data, 1, cfi->dev_size, fp);
+	  else
+	    read_len = 0;
+
+	  /* Don't need to fclose() with fdopen("r").  */
+	}
+      else
+	read_len = 0;
+
+      memset (cfi->data, 0xff, cfi->dev_size - read_len);
+    }
+
+  close (fd);
+}
+
+/* Once we've been declared in the device tree, this is the main
+   entry point. So allocate state, attach memory addresses, and
+   all that fun stuff.  */
+static void
+cfi_finish (struct hw *me)
+{
+  struct cfi *cfi;
+
+  cfi = HW_ZALLOC (me, struct cfi);
+
+  set_hw_data (me, cfi);
+  set_hw_io_read_buffer (me, cfi_io_read_buffer);
+  set_hw_io_write_buffer (me, cfi_io_write_buffer);
+  set_hw_delete (me, cfi_delete_callback);
+
+  attach_cfi_regs (me, cfi);
+
+  /* Initialize the CFI.  */
+  cfi->state = CFI_STATE_READ;
+  memcpy (cfi->query.qry, "QRY", 3);
+  cfi->cmdset->setup (me, cfi);
+}
+
+/* Every device is required to declare this.  */
+const struct hw_descriptor dv_cfi_descriptor[] =
+{
+  {"cfi", cfi_finish,},
+  {NULL, NULL},
+};
diff --git a/sim/common/dv-cfi.h b/sim/common/dv-cfi.h
new file mode 100644
index 0000000..bd2db2d
--- /dev/null
+++ b/sim/common/dv-cfi.h
@@ -0,0 +1,60 @@
+/* Common Flash Memory Interface (CFI) model.
+
+   Copyright (C) 2010 Free Software Foundation, Inc.
+   Contributed by Analog Devices, Inc.
+
+   This file is part of simulators.
+
+   This program is free software; you can redistribute it and/or modify
+   it under the terms of the GNU General Public License as published by
+   the Free Software Foundation; either version 3 of the License, or
+   (at your option) any later version.
+
+   This program is distributed in the hope that it will be useful,
+   but WITHOUT ANY WARRANTY; without even the implied warranty of
+   MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+   GNU General Public License for more details.
+
+   You should have received a copy of the GNU General Public License
+   along with this program.  If not, see <http://www.gnu.org/licenses/>.  */
+
+#ifndef DV_CFI_H
+#define DV_CFI_H
+
+/* CFI standard.  */
+#define CFI_CMD_CFI_QUERY		0x98
+#define CFI_ADDR_CFI_QUERY_START	0x55
+#define CFI_ADDR_CFI_QUERY_RESULT	0x10
+
+#define CFI_CMD_READ			0xFF
+#define CFI_CMD_RESET			0xF0
+#define CFI_CMD_READ_ID			0x90
+
+/* Intel specific.  */
+#define CFI_CMDSET_INTEL		0x0001
+#define INTEL_CMD_STATUS_CLEAR		0x50
+#define INTEL_CMD_STATUS_READ		0x70
+#define INTEL_CMD_WRITE			0x40
+#define INTEL_CMD_WRITE_ALT		0x10
+#define INTEL_CMD_WRITE_BUFFER		0xE8
+#define INTEL_CMD_WRITE_BUFFER_CONFIRM	0xD0
+#define INTEL_CMD_LOCK_SETUP		0x60
+#define INTEL_CMD_LOCK_BLOCK		0x01
+#define INTEL_CMD_UNLOCK_BLOCK		0xD0
+#define INTEL_CMD_LOCK_DOWN_BLOCK	0x2F
+#define INTEL_CMD_ERASE_BLOCK		0x20
+#define INTEL_CMD_ERASE_CONFIRM		0xD0
+
+/* Intel Status Register bits.  */
+#define INTEL_SR_BWS		(1 << 0)	/* BEFP Write.  */
+#define INTEL_SR_BLS		(1 << 1)	/* Block Locked.  */
+#define INTEL_SR_PSS		(1 << 2)	/* Program Suspend.  */
+#define INTEL_SR_VPPS		(1 << 3)	/* Vpp.  */
+#define INTEL_SR_PS		(1 << 4)	/* Program.  */
+#define INTEL_SR_ES		(1 << 5)	/* Erase.  */
+#define INTEL_SR_ESS		(1 << 6)	/* Erase Suspend.  */
+#define INTEL_SR_DWS		(1 << 7)	/* Device Write.  */
+
+#define INTEL_ID_MANU		0x89
+
+#endif
-- 
1.7.4.1

Re: [PATCH v4] sim: cfi: new flash device simulation

[Joel Brobecker]

> gdb/:
> 2011-03-24  Mike Frysinger  <vapier@gentoo.org>
> 
> 	* NEWS: Mention new cfi device simulation.
> 
> sim/common/:
> 2011-03-24  Mike Frysinger  <vapier@gentoo.org>
> 
> 	* aclocal.m4 (SIM_AC_OPTION_HARDWARE): Add cfi to default list.
> 	* Make-common.in (dv-cfi.o): New rule.
> 	* dv-cfi.c, dv-cfi.h: New files.

This is OK. I think you answered the only comment by adding the warning
whem mmap is not available.

-- 
Joel

Re: [PATCH v4] sim: cfi: new flash device simulation

[Mike Frysinger]

On Tue, Mar 29, 2011 at 11:40 AM, Joel Brobecker wrote:
>> gdb/:
>> 2011-03-24  Mike Frysinger  <vapier@gentoo.org>
>>
>>       * NEWS: Mention new cfi device simulation.
>>
>> sim/common/:
>> 2011-03-24  Mike Frysinger  <vapier@gentoo.org>
>>
>>       * aclocal.m4 (SIM_AC_OPTION_HARDWARE): Add cfi to default list.
>>       * Make-common.in (dv-cfi.o): New rule.
>>       * dv-cfi.c, dv-cfi.h: New files.
>
> This is OK. I think you answered the only comment by adding the warning
> whem mmap is not available.

thanks.  ive also regenerated the bfin/configure so that it includes
cfi in its build now.
-mike