Re: help with remote debug!!

Re: help with remote debug!!

[Quality Quorum]

On Tue, 18 Jul 2000 chester@linux.org.tw wrote:

> Hi....!
> I got some confuse about remote debug feature on gdb.
> (I have read some GDB doc).
> Build all of cross-compile in my PC for StrongARM and bootable
> kernel that uses cross-compile.
> Then i do the following command,
> $ arm-unknown-linux-gdb vmlinux
> 
> and,
> (gdb) set remotebaud 115200
> (gdb) target remote /dev/ttyS0
> (gdb) run
> 
> But it hang on connect to remote target,no message on my terminal.
> 
> What can i do for it ?? Or more doc i can study??

Steps are as follows:

1. Find/adapt/develop gdb stub for ARM processor.

2. Hook it up the serial driver on the target.

3. Link it into your image.

4. Activate it upon start up.

> 
> Thanks,
> 				Chester
> 

Thanks,

Aleksey

Re: help with remote debug!!

[Jim Ingham]

Also sprach chester@linux.org.tw:

> Hi....!
> I got some confuse about remote debug feature on gdb.
> (I have read some GDB doc).
> Build all of cross-compile in my PC for StrongARM and bootable
> kernel that uses cross-compile.
> Then i do the following command,
> $ arm-unknown-linux-gdb vmlinux
> 
> and,
> (gdb) set remotebaud 115200
> (gdb) target remote /dev/ttyS0
> (gdb) run
> 
> But it hang on connect to remote target,no message on my terminal.
> 
> What can i do for it ?? Or more doc i can study??
> 
> Thanks,
> Chester
> 
> 
You want to use the same device that Fernando suggested in the previous
message.  Before you issue the "target remote" command, say:

(gdb) set debug remote 2

Then you will get a trace of all the messages flowing between you and your
stub.  You can see if you ever connect, or if there is some errors in the
initial handshake that are causing the hang.

The gdb info file has a section on the remote protocol, which will help you
understand the traffic you are watching.

Jim
-- 
Jim Ingham                                 jingham@apple.com
Apple Computer

Re: help with remote debug!!

[Andrew Cagney]

[-- Warning: decoded text below may be mangled, UTF-8 assumed --]
[-- Attachment #1: Type: text/plain, Size: 1825 bytes --]

chester@linux.org.tw wrote:
> 
> Hi....!
> I got some confuse about remote debug feature on gdb.
> (I have read some GDB doc).
> Build all of cross-compile in my PC for StrongARM and bootable
> kernel that uses cross-compile.
> Then i do the following command,

From memory, adding the GDB stub to the Linux kernel was only a recent
inovation.  I guess, the kernel stub code is enabled and is known to
work.  Does that stub code come with a Linux HOWTO tht is specific to
the arm?

> $ arm-unknown-linux-gdb vmlinux
> 
> and,
> (gdb) set remotebaud 115200
> (gdb) target remote /dev/ttyS0

Ok so far. (should I also mention set debug remote ...? :-)

> (gdb) run

this looks wrong. If I assume that you've set up:

  <gdb vmlinux> - /dev/ttyS0 ------ arm board with kernel

then I don't know that ``run'' is applicable.

One guess of what should happen is:

	o	the arm board boots the kernel

	o	the arm board traps to the
		sub

	o	you connect gdb to the serial
		line connected to the arm board

	o	after entering ``target remote...''
		you can examine the kernel state

	o	use continue (not run) to resume
		execution

	Andrew



> 
> But it hang on connect to remote target,no message on my terminal.
> 
> What can i do for it ?? Or more doc i can study??
> 
> Thanks,
>                                 Chester
From gerwynd@tommoll.freeserve.co.uk Thu Jul 20 04:03:00 2000
From: "Gerwyn Davies" <gerwynd@tommoll.freeserve.co.uk>
To: "GDB" <gdb@sourceware.cygnus.com>
Subject: Connecting to Insight
Date: Thu, 20 Jul 2000 04:03:00 -0000
Message-id: <000701bff23a$96e0c0c0$aeb8883e@gtd-s-machine>
X-SW-Source: 2000-07/msg00065.html
Content-length: 162

Hi,
 
Anyone know of the RS232 pinout require to 
connect Insight ( hosted on a PC, is it available for any other hosts?) to a 
remote target?
 
Thanks.