Re: [RFC] Only compute realpath when basenames_may_differ is set

Jonah Graham
2019-09-12T17:47:57Z

bump.

On Mon, 19 Aug 2019 at 15:25, Jonah Graham <jonah@kichwacoders.com> wrote:

>
> On Fri, 14 Jun 2019 at 10:31, Tom Tromey <tromey@adacore.com> wrote:
>
>> I'm checking this in now.
>>
>> Tom
>>
>
> Hi Tom,
>
> This causes an error with Eclipse CDT's default use case. In CDT the
> compile lines are basically "gcc -g -c -o file.o ../file.c" with the pwd
> being a directory under the source:
>
> root/
> file.c
> Debug/
> Makefile
> file.o
> program.elf
>
> I have modified the fullname.exp test with a testcase that shows the
> failure, see the patch below. Here is also a short trace of a session
> showing the problem:
>
> /tmp $ mkdir test && cd test
> /tmp/test $ echo 'int main() {}' > testcase.c
> /tmp/test $ mkdir build && cd build
> /tmp/test/build $ gcc -g ../testcase.c -o testcase
> /tmp/test/build $ gdb -q testcase
> Reading symbols from testcase...done.
> (gdb) b /tmp/test/testcase.c:1
> Breakpoint 1 at 0x603: file ../testcase.c, line 1.
> (gdb) quit
> /tmp/test/build $ /scratch/gdb/binutils-gdb/gdb/gdb -q testcase
> Reading symbols from testcase...
> (gdb) b /tmp/test/testcase.c:1
> No source file named /tmp/test/testcase.c.
> Make breakpoint pending on future shared library load? (y or [n]) n
> (gdb) quit
> /tmp/test/build $ gdb --version | head -1
> GNU gdb (Ubuntu 8.1-0ubuntu3) 8.1.0.20180409-git
> /tmp/test/build $ /scratch/gdb/binutils-gdb/gdb/gdb --version | head -1
> GNU gdb (GDB) 8.3.50.20190819-git
>
> Thanks,
> Jonah
>
> ---
> gdb/testsuite/gdb.base/fullname.exp | 30 +++++++++++++++++++++++++++++
> 1 file changed, 30 insertions(+)
>
> diff --git a/gdb/testsuite/gdb.base/fullname.exp
> b/gdb/testsuite/gdb.base/fullname.exp
> index 07d6245d15..e306400b2b 100644
> --- a/gdb/testsuite/gdb.base/fullname.exp
> +++ b/gdb/testsuite/gdb.base/fullname.exp
> @@ -96,6 +96,36 @@ if { [gdb_breakpoint [standard_output_file
> tmp-${srcfile}]:${line} {no-message}]
> fail $msg
> }
>
> +# Build the test executable using a relative path with /../ .
> +file mkdir [standard_output_file ""]/build
> +with_cwd [standard_output_file ""]/build {
> + if { [gdb_compile ../tmp-${srcfile} \
> + "${binfile}" executable {debug}] != "" } {
> + return -1
> + }
> +
> + gdb_exit
> + gdb_start
> + gdb_load ${binfile}
> +
> + set msg "set breakpoint by full path before loading symbols - built
> relative with .."
> + if { [gdb_breakpoint [standard_output_file tmp-${srcfile}]:${line}
> {no-message}] != 0 } {
> + pass $msg
> + } else {
> + fail $msg
> + }
> +
> + gdb_test "break main" \
> + "Breakpoint.*at.*line.*" "set breakpoint at main - built relative
> with .."
> +
> + set msg "set breakpoint by full path after loading symbols - built
> relative with .."
> + if { [gdb_breakpoint [standard_output_file tmp-${srcfile}]:${line}
> {no-message}] != 0 } {
> + pass $msg
> + } else {
> + fail $msg
> + }
> +}
> +
> # Build the test executable using relative paths not relative to the
> directory
> # we'll run GDB from.
>
> --
> 2.22.0
>