Hi,

this patch replaces most of the current_gdbarch's found in *mips*. These replacements are mostly
mechanical changes. Unfortunately I dont have access to MIPS (linux, bsd, remote) machines.
This patch is hence only "tested" by building GDB with --enable-targets=all.

Maybe someone from you can run the testsuite with the patch attached? Thanks in advance.


ChangeLog:

	* mips-tdep.c (fp_register_arg_p): Add gdbarch as paramter.
	(mips_n32n64_push_dummy_call, mips_o64_return_value)
	(mips_eabi_push_dummy_call): Update call to fp_register_arg_p.

	(MIPS_FPU_TYPE): Add gdbarch as parameter and replace current_gdbarch.
	(fp_register_arg_p, mips_dump_tdep, show_mipsfpu_command)
	(mips_n32n64_fp_arg_chunk_p): Update caller.

	(mips_n32n64_fp_arg_chunk_p): Add gdbarch as paramter.
	(mips_n32n64_push_dummy_call): Update caller.

	(MIPS_LAST_ARG_REGNUM): Add gdbarch as parameter and replace
	current_gdbarch.
	(mips_eabi_push_dummy_call, mips_n32n64_push_dummy_call)
	(mips_o32_push_dummy_call, mips_o64_push_dummy_call): Update caller.

	(MIPS_LAST_FP_ARG_REGNUM): Add gdbarch as parameter and replace
	current_gdbarch.
	(mips_eabi_push_dummy_call, mips_o32_push_dummy_call)
	(mips_o64_push_dummy_call): Update caller.

	(MIPS_EABI): Add gdbarch as parameter and replace current_gdbarch.
	(fp_register_arg_p, mips_dump_tdep): Update caller.

	(set_reg_offset): Add gdbarch as parameter and replace current_gdbarch.
	(mips16_scan_prologue, mips32_scan_prologue): Update caller.

	(reset_saved_regs): Make static.  Add gdbarch as parameter.  Replace
	current_gdbarch.
	(mips32_scan_prologue): Update caller.

	(heuristic_proc_start): Add gdbarch as parameter. Replace
	current_gdbarch.
	(mips_insn16_frame_cache, mips_insn32_frame_cache): Update caller.

	* mipsnbsd-nat.c (mipsnbsd_fetch_inferior_registers)
	(mipsnbsd_store_inferior_registers): Use get_regcache_arch to get at
	the current architecture. Update call to getregs_supplies.
	(getregs_supplies): Add gdbarch as parameter and replace
	current_gdbarch.

	* mipsnbsd-tdep.c (mipsnbsd_get_longjmp_target): Use get_frame_arch to
	get at the current architecture. Update call to NBSD_MIPS_JB_OFFSET and
	NBSD_MIPS_JB_ELEMENT_SIZE.
	(NBSD_MIPS_JB_ELEMENT_SIZE, NBSD_MIPS_JB_OFFSET): Add gdbarch and
	replace current_gdbarch.

	* remote-mips.c (mips_map_regno): Add gdbarch as parameter and replace
	current_gdbarch.
	(mips_fetch_registers, mips_store_registers): Update call
	to mips_map_regno.
	(mips_load): Use get_regcache_arch to get at the current_architecture
	and replace current_gdbarch.

Regards,
Markus

-- 
  Markus Deuling
  GNU Toolchain for Linux on Cell BE
  deuling@de.ibm.com